6.2A.2 UE maximum output power reduction for CA
38.521-23GPPNRPart 2: Range 2 standaloneRadio transmission and receptionRelease 16TSUser Equipment (UE) conformance specification
6.2A.2.0 Minimum conformance requirements
6.2A.2.0.1 General
The UE is defined to be configured for CA operation when it has at least one of UL or DL configured for CA. In CA operation, the UE may reduce its maximum output power due to higher order modulations and transmit bandwidth configurations. This Maximum Power Reduction (MPR) is defined in subclauses below.
When the maximum output power of a UE is modified by MPR, the power limits specified in subclause 6.2A.4.0 apply.
The requirements in the following subclauses are only applicable to intra-band contiguous uplink CA, with the aggregated channel bandwidth up to 800 MHz.
6.2A.2.0.2 Maximum output power reduction for power class 1
For power class 1, MPR for UL contiguous allocations within the cumulative aggregated bandwidth is defined as:
MPRC_CA = max(MPRWT_C_CA, MPRnarrow)
Where,
MPRnarrow = 14.4 dB, when BWalloc,RB is less than or equal to 1.44 MHz, MPRnarrow = 10 dB, when 1.44 MHz < BWalloc,RB ≤ 10.8 MHz, where BWalloc,RB is the bandwidth of the RB allocation size.
MPRWT_C_CA is the maximum power reduction due to modulation orders, transmit bandwidth configurations, and waveform types. MPRWT_contiguous is defined in Table 6.2A.2.2-1.
Table 6.2A.2.0-1: Maximum power reduction (MPRWT_C_CA) for UE power class 1
|
Waveform Type |
Cumulative aggregated channel bandwidth |
|||
|
< 400 MHz |
≥ 400 MHz and < 800 MHz |
≥ 800 MHz and ≤ 1400 MHz |
||
|
DFT-s-OFDM |
Pi/2 BPSK |
≤ 5.51 |
7.71 |
[8.2] |
|
QPSK |
≤ 6.51 |
8.71 |
[9.7] |
|
|
16 QAM |
≤ 6.5 |
8.7 |
[9.2] |
|
|
64 QAM |
≤ 9.0 |
10.7 |
[11.2] |
|
|
CP-OFDM |
QPSK |
≤ 6.5 |
8.7 |
[8.7] |
|
16 QAM |
≤ 6.5 |
8.7 |
[8.7] |
|
|
64 QAM |
≤ 9.0 |
10.7 |
[11.2] |
|
|
NOTE 1: The following condition applies only when the cumulative aggregated BW of the CA configuration 400MHz. For a contiguous RB allocation in a single CC of the CA configuration, the single CC MPR of subclause 6.2.2.1 applies. The cumulative aggregated bandwidth shall be used as BWchannel in Tables 6.2.2.1-1 and 6.2.2.1-2. The applicable column in Tables 6.2.2.1-1 and 6.2.2.1-2 shall be determined based on the transmission bandwidth of the CA allocation in relation to the allocation regions defined in the tables. |
||||
When different waveform types exist across CCs, the requirement is set by the waveform type used in the configuration with the largest MPRC_CA.
For non-contiguous RB allocations, the following rule for MPR applies:
MPR = max(MPRC_CA, -10*A + [14.4])
Where:
A = NRB_alloc / NRB_agg_C.
NRB_alloc is the total number of allocated UL RBs
NRB_agg_C is the number of the aggregated RBs within the fully allocated cumulative aggregated channel bandwidth
6.2A.2.0.3 Maximum output power reduction for power class 2
For power class 2, MPR specified in sub-clause 6.2A.2.0.4 applies.
Table 6.2A.2.0.3-1: (Void)
6.2A.2.0.4 Maximum output power reduction for power class 3
For power class 3, MPR for UL contiguous allocations within the cumulative aggregated bandwidth is denoted as MPRC_CA and is defined in Table 6.2A.2.0.4-1.
Table 6.2A.2.0.4-1: Maximum power reduction (MPRC_CA) for UE power class 3
|
Cumulative aggregated bandwidth configuration |
||||
|
≤ 400 MHz |
> 400 MHz and < 800 MHz |
≥ 800 MHz and ≤ 1400 MHz |
||
|
DFT-s-OFDM |
Pi/2 BPSK |
≤ 5.01 |
≤ 7.71 |
≤ [8.2] |
|
QPSK |
≤ 5.01 |
≤ 7.71 |
≤ [8.2] |
|
|
16 QAM |
≤ 6.5 |
≤ 8.7 |
≤ [9.3] |
|
|
64 QAM |
≤ 9.0 |
≤ 10.7 |
≤ [11.2] |
|
|
CP-OFDM |
QPSK |
≤ 5.0 |
≤ 7.5 |
≤ [8.0] |
|
16 QAM |
≤ 6.5 |
≤ 8.7 |
≤ [9.2] |
|
|
64 QAM |
≤ 9.0 |
≤ 10.7 |
≤ [11.2] |
|
When different waveform types exist across CCs, the requirement is set by the waveform type used in the configuration with the highest contiguous MPR.
For non-contiguous RB allocations, the following rule for MPR applies:
MPR = max(MPRC_CA, -10*A +7.0)
Where:
A = NRB_alloc / NRB_agg_C.
NRB_alloc is the total number of allocated UL RBs
NRB_agg_C is the number of the aggregated RBs within the fully allocated cumulative aggregated channel bandwidth
6.2A.2.0.5 Maximum output power reduction for power class 4
For power class 4, MPR specified in sub-clause 6.2A.2.0.4 applies.
The normative reference for this requirement is TS 38.101-2 [3] clause 6.2A.2.
6.2A.2.1 UE maximum output power reduction for CA (2UL CA)
Editor’s note: This clause is incomplete. The following aspects are either missing or not yet determined:
– Measurement Uncertainties and Test Tolerances are FFS for power class 1, 2 and 4.
– Measurement Uncertainties and Test Tolerances for intra-band contiguous CA supporting aggregated BW > 400MHz and intra-band non-contiguous CA are TBD.
– Whether to further divide this test case considering the number of DL CC is FFS
- TP analysis needs further update to reflect the selection of applicable cumulative aggregated BW
– Following aspects are pending RAN4
Minimum requirements for cumulative aggregated bandwidth >=800MHz are within brackets
T(MPR) in 6.2A.4 configured output power is within brackets.
This test case is incomplete until a suitable solution for preventing SCell drop is implemented in the test procedure.
6.2A.2.1.1 Test purpose
The number of RB identified in 6.2.2.3 is based on meeting the requirements for the maximum power reduction (MPR) due to Cubic Metric (CM).
6.2A.2.1.2 Test applicability
The requirements of this test apply to all types of NR UE release 15 and forward supporting 2UL CA.
6.2A.2.1.3 Minimum conformance requirements
The normative reference for this requirement is TS 38.101-2 [3] clause 6.2A.2.0.
6.2A.2.1.4 Test description
6.2A.2.1.4.1 Initial conditions
Initial conditions are a set of test configurations the UE needs to be tested in and the steps for the SS to take with the UE to reach the correct measurement state.
The initial test configurations consist of environmental conditions, test frequencies, and CC combinations based on NR operating bands specified in Table 5.5A.1-1, 5.5A.2-1 and 5.5A.2-2. All of these configurations shall be tested with applicable test parameters for each CA configuration and subcarrier spacing, are shown in table 6.2A.2.1.4.1-1. The details of the uplink reference measurement channels (RMCs) are specified in Annexes A.2. Configurations of PDSCH and PDCCH before measurement are specified in Annex C.2.
Table 6.2A.2.1.4.1-1: Intra-band Contiguous UL CA Test Configuration Table (Power Class 1, MPRnarrow)
|
Default Conditions |
||||||
|
Test Environment as specified in TS 38.508-1 [10] subclause 4.1 |
Normal |
|||||
|
Test Frequencies as specified in TS 38.508-1 [10] subclause 4.3.1.2.3 for different CA bandwidth classes |
Refer to “Test frequency” column |
|||||
|
Test CC Combination setting (aggregated BW of the CA configuration) as specified in Table 5.5A.1-1, 5.5A.2-1 and 5.5A.2-2 for the CA Configuration across bandwidth combination sets supported by the UE |
Highest aggregated channel bandwidth of the CA configuration |
|||||
|
Test SCS as specified in Table 5.3.5-1 |
120 kHz |
|||||
|
Test Parameters |
||||||
|
Test ID |
CC & Mapping (NOTE 2) |
ChBw(MHz) |
Test frequency |
DL RB allocation |
UL Modulation |
UL RB allocation (NOTE 1) |
|
Default Test Settings for a CA_nXB, CA_nXD, CA_nXG, CA_nXO Configuration |
||||||
|
1 |
PCC/CC1 |
Default |
Low |
N/A for this |
CP-OFDM 64QAM |
Outer_1RB_Left |
|
SCC/CC2 |
Low |
test |
– |
– |
||
|
2 |
PCC/CC1 |
High |
CP-OFDM 64QAM |
Outer_1RB_Right |
||
|
SCC/CC2 |
High |
– |
– |
|||
|
3 |
PCC/CC1 |
Low |
CP-OFDM 64QAM |
7@0 |
||
|
SCC/CC2 |
Low |
– |
– |
|||
|
4 |
PCC/CC1 |
High |
CP-OFDM 64QAM |
7@NRB-7 |
||
|
SCC/CC2 |
High |
– |
– |
|||
|
Default Test Settings for a CA_nX(D-G)_UL_nXD, CA_nX(D-G)_UL_nXG, CA_nX(D-O)_UL_nXD, CA_nX(D-O)_UL_nXO Configuration |
||||||
|
1 |
PCC/CC1 |
Default |
Low |
N/A for this |
CP-OFDM 64QAM |
Outer_1RB_Left |
|
SCC1/CC2 |
Low |
test |
– |
– |
||
|
Wgap |
Max Wgap |
N/A |
N/A |
|||
|
SCC2/CC3 |
Low |
N/A |
N/A |
|||
|
SCC3/CC4 |
Low |
N/A |
N/A |
|||
|
2 |
PCC/CC1 |
High |
CP-OFDM 64QAM |
Outer_1RB_Right |
||
|
SCC1/CC2 |
High |
– |
– |
|||
|
Wgap |
Max Wgap |
N/A |
N/A |
|||
|
SCC2/CC3 |
High |
N/A |
N/A |
|||
|
SCC3/CC4 |
High |
N/A |
N/A |
|||
|
3 |
PCC/CC1 |
Low |
CP-OFDM 64QAM |
7@0 |
||
|
SCC1/CC2 |
Low |
– |
– |
|||
|
Wgap |
Max Wgap |
N/A |
N/A |
|||
|
SCC2/CC3 |
Low |
N/A |
N/A |
|||
|
SCC3/CC4 |
Low |
N/A |
N/A |
|||
|
4 |
PCC/CC1 |
High |
CP-OFDM 64QAM |
7@NRB-7 |
||
|
SCC1/CC2 |
High |
– |
– |
|||
|
Wgap |
Max Wgap |
N/A |
N/A |
|||
|
SCC2/CC3 |
High |
N/A |
N/A |
|||
|
SCC3/CC4 |
High |
N/A |
N/A |
|||
|
Default Test Settings for a CA_nX(D-H)_UL_nXD, CA_nX(D-P)_UL_nXD, CA_nX(E-O)_UL_nXO Configuration |
||||||
|
1 |
PCC/CC1 |
Default |
Low |
N/A for this |
CP-OFDM 64QAM |
Outer_1RB_Left |
|
SCC1/CC2 |
Low |
test |
– |
– |
||
|
Wgap |
Max Wgap |
N/A |
N/A |
|||
|
SCC2/CC3 |
Low |
N/A |
N/A |
|||
|
SCC3/CC4 |
Low |
N/A |
N/A |
|||
|
SCC4/CC5 |
Low |
N/A |
N/A |
|||
|
2 |
PCC/CC1 |
High |
CP-OFDM 64QAM |
Outer_1RB_Right |
||
|
SCC1/CC2 |
High |
– |
– |
|||
|
Wgap |
Max Wgap |
N/A |
N/A |
|||
|
SCC2/CC3 |
High |
N/A |
N/A |
|||
|
SCC3/CC4 |
High |
N/A |
N/A |
|||
|
SCC4/CC5 |
High |
N/A |
N/A |
|||
|
3 |
PCC/CC1 |
Low |
CP-OFDM 64QAM |
7@0 |
||
|
SCC1/CC2 |
Low |
– |
– |
|||
|
Wgap |
Max Wgap |
N/A |
N/A |
|||
|
SCC2/CC3 |
Low |
N/A |
N/A |
|||
|
SCC3/CC4 |
Low |
N/A |
N/A |
|||
|
SCC4/CC5 |
Low |
N/A |
N/A |
|||
|
4 |
PCC/CC1 |
High |
CP-OFDM 64QAM |
7@NRB-7 |
||
|
SCC1/CC2 |
High |
– |
– |
|||
|
Wgap |
Max Wgap |
N/A |
N/A |
|||
|
SCC2/CC3 |
High |
N/A |
N/A |
|||
|
SCC3/CC4 |
High |
N/A |
N/A |
|||
|
SCC4/CC5 |
High |
N/A |
N/A |
|||
|
Default Test Settings for a CA_nX(D-I)_UL_nXD, CA_nX(D-Q)_UL_nXD, CA_nX(G-I)_UL_nXG Configuration |
||||||
|
1 |
PCC/CC1 |
Default |
Low |
N/A for this |
CP-OFDM 64QAM |
Outer_1RB_Left |
|
SCC1/CC2 |
Low |
test |
– |
– |
||
|
Wgap |
Max Wgap |
N/A |
N/A |
|||
|
SCC2/CC3 |
Low |
N/A |
N/A |
|||
|
SCC3/CC4 |
Low |
N/A |
N/A |
|||
|
SCC4/CC5 |
Low |
N/A |
N/A |
|||
|
SCC5/CC6 |
Low |
N/A |
N/A |
|||
|
2 |
PCC/CC1 |
High |
CP-OFDM 64QAM |
Outer_1RB_Right |
||
|
SCC1/CC2 |
High |
– |
– |
|||
|
Wgap |
Max Wgap |
N/A |
N/A |
|||
|
SCC2/CC3 |
High |
N/A |
N/A |
|||
|
SCC3/CC4 |
High |
N/A |
N/A |
|||
|
SCC4/CC5 |
High |
N/A |
N/A |
|||
|
SCC5/CC6 |
High |
N/A |
N/A |
|||
|
3 |
PCC/CC1 |
Low |
CP-OFDM 64QAM |
7@0 |
||
|
SCC1/CC2 |
Low |
– |
– |
|||
|
Wgap |
Max Wgap |
N/A |
N/A |
|||
|
SCC2/CC3 |
Low |
N/A |
N/A |
|||
|
SCC3/CC4 |
Low |
N/A |
N/A |
|||
|
SCC4/CC5 |
Low |
N/A |
N/A |
|||
|
SCC5/CC6 |
Low |
N/A |
N/A |
|||
|
4 |
PCC/CC1 |
High |
CP-OFDM 64QAM |
7@NRB-7 |
||
|
SCC1/CC2 |
High |
– |
– |
|||
|
Wgap |
Max Wgap |
N/A |
N/A |
|||
|
SCC2/CC3 |
High |
N/A |
N/A |
|||
|
SCC3/CC4 |
High |
N/A |
N/A |
|||
|
SCC4/CC5 |
High |
N/A |
N/A |
|||
|
SCC5/CC6 |
High |
N/A |
N/A |
|||
|
NOTE 1: The specific configuration of each RB allocation is defined in Table 6.1-2. NOTE 2: PCC/CCi and SCC/CCj means PCC is on component carrier CCi and SCC is on component carrier CCj, with CCi or CCj frequencies defined in TS38.508-1 [10]. |
||||||
Table 6.2A.2.1.4.1-2: Intra-band Contiguous UL CA Test Configuration Table (Power Class 1, single CC MPR requirement)
|
Default Conditions |
||||||
|
Test Environment as specified in TS 38.508-1 [10] subclause 4.1 |
Normal |
|||||
|
Test Frequencies as specified in TS 38.508-1 [10] subclause 4.3.1.2.3 for different CA bandwidth classes |
Lowest range, Highest range |
|||||
|
Test CC Combination setting (aggregated BW of the CA configuration) as specified in Table 5.5A.1-1, 5.5A.2-1 and 5.5A.2-2 for the CA Configuration across bandwidth combination sets supported by the UE |
Highest aggregated channel bandwidth of the CA configuration |
|||||
|
Test SCS as specified in Table 5.3.5-1 |
120 kHz |
|||||
|
Test Parameters |
||||||
|
Test ID |
CC & Mapping (NOTE 2) |
ChBw(MHz) |
Test frequency |
DL RB allocation |
UL Modulation |
UL RB allocation |
|
Default Test Settings for a CA_nXG, CA_nXO Configuration (Cumulative aggregated BWchannel <= 200MHz) |
||||||
|
1 |
PCC/CC1 |
Default |
Default |
N/A for this |
DFT-s-OFDM PI/2 BPSK |
Outer_Full |
|
SCC/CC2 |
test |
– |
– |
|||
|
2 |
PCC/CC1 |
DFT-s-OFDM QPSK |
Inner_Full_Region1 |
|||
|
SCC/CC2 |
– |
– |
||||
|
Default Test Settings for a CA_nXD Configuration (Cumulative aggregated BWchannel <= 400MHz) |
||||||
|
1 |
PCC/CC1 |
Default |
Default |
N/A for this |
DFT-s-OFDM PI/2 BPSK |
Outer_Full |
|
SCC/CC2 |
test |
– |
– |
|||
|
2 |
PCC/CC1 |
DFT-s-OFDM PI/2 BPSK |
Inner_Full_Region1 |
|||
|
SCC/CC2 |
– |
– |
||||
|
3 |
PCC/CC1 |
DFT-s-OFDM QPSK |
Inner_Full_Region1 |
|||
|
SCC/CC2 |
– |
– |
||||
|
NOTE 1: The specific configuration of each RB allocation is defined in Table 6.1-2. NOTE 2: PCC/CCi and SCC/CCj means PCC is on component carrier CCi and SCC is on component carrier CCj, with CCi or CCj frequencies defined in TS38.508-1 [10]. NOTE 3: DFT-s-OFDM PI/2 BPSK test applies only for UEs which supports half Pi BPSK in FR1. |
||||||
Table 6.2A.2.1.4.1-3: Intra-band Contiguous UL CA Test Configuration Table (Power Class 1, MPRC_CA)
|
Default Conditions |
||||||
|
Test Environment as specified in TS 38.508-1 [10] subclause 4.1 |
Normal |
|||||
|
Test Frequencies as specified in TS 38.508-1 [10] subclause 4.3.1.2.3 for different CA bandwidth classes |
For intra-band contiguous CA: Mid range. For intra-band non-contiguous CA: Lowest range with Max Wgap, Highest range with Max Wgap. |
|||||
|
Test CC Combination setting (aggregated BW of the CA configuration) as specified in Table 5.5A.1-1, 5.5A.2-1 and 5.5A.2-2 for the CA Configuration across bandwidth combination sets supported by the UE |
Highest aggregated channel bandwidth of the CA configuration |
|||||
|
Test SCS as specified in Table 5.3.5-1 |
120 kHz |
|||||
|
Test Parameters |
||||||
|
Test ID |
CC& Mapping (NOTE 2) |
ChBw(MHz) |
Test frequency |
DL RB allocation |
UL Modulation |
UL RB allocation |
|
Default Test Settings for a CA_nXB, CA_nXC_UL_nXB Configuration (800MHz <= Cumulative aggregated BWchannel <= 1400MHz) |
||||||
|
1 |
PCC/CC1 |
Default |
Default |
N/A for this |
DFT-s-OFDM Pi/2 BPSK |
Outer_Full |
|
SCC/CC2 |
test |
DFT-s-OFDM Pi/2 BPSK |
Outer_Full |
|||
|
2 |
PCC/CC1 |
DFT-s-OFDM QPSK |
Outer_Full |
|||
|
SCC/CC2 |
DFT-s-OFDM QPSK |
Outer_Full |
||||
|
3 |
PCC/CC1 |
DFT-s-OFDM 16QAM |
Outer_Full |
|||
|
SCC/CC2 |
DFT-s-OFDM 16QAM |
Outer_Full |
||||
|
4 |
PCC/CC1 |
CP-OFDM 16QAM |
Outer_Full |
|||
|
SCC/CC2 |
CP-OFDM 16QAM |
Outer_Full |
||||
|
5 |
PCC/CC1 |
CP-OFDM 64QAM |
Outer_Full |
|||
|
SCC/CC2 |
CP-OFDM 64QAM |
Outer_Full |
||||
|
Default Test Settings for a CA_nXD Configuration (400MHz <= Cumulative aggregated BWchannel < 800MHz) |
||||||
|
1 |
PCC/CC1 |
Default |
Default |
N/A for this |
DFT-s-OFDM Pi/2 BPSK |
Outer_Full |
|
SCC/CC2 |
test |
DFT-s-OFDM Pi/2 BPSK |
Outer_Full |
|||
|
2 |
PCC/CC1 |
CP-OFDM 16QAM |
Outer_Full |
|||
|
SCC/CC2 |
CP-OFDM 16QAM |
Outer_Full |
||||
|
3 |
PCC/CC1 |
CP-OFDM 64QAM |
Outer_Full |
|||
|
SCC/CC2 |
CP-OFDM 64QAM |
Outer_Full |
||||
|
Default Test Settings for a CA_nXB Configuration (400MHz <= Cumulative aggregated BWchannel < 800MHz) |
||||||
|
1 |
PCC/CC1 |
200MHz |
Default |
N/A for this |
DFT-s-OFDM Pi/2 BPSK |
Outer_Full |
|
SCC/CC2 |
400MHz |
test |
DFT-s-OFDM Pi/2 BPSK |
Outer_Full |
||
|
2 |
PCC/CC1 |
200MHz |
CP-OFDM 16QAM |
Outer_Full |
||
|
SCC/CC2 |
400MHz |
CP-OFDM 16QAM |
Outer_Full |
|||
|
3 |
PCC/CC1 |
200MHz |
CP-OFDM 64QAM |
Outer_Full |
||
|
SCC/CC2 |
400MHz |
CP-OFDM 64QAM |
Outer_Full |
|||
|
Default Test Settings for a CA_nXG, CA_nXO Configuration (Cumulative aggregated BWchannel < 400MHz) |
||||||
|
1 |
PCC/CC1 |
Default |
Default |
N/A for this |
DFT-s-OFDM Pi/2 BPSK |
Outer_Full |
|
SCC/CC2 |
test |
DFT-s-OFDM Pi/2 BPSK |
Outer_Full |
|||
|
2 |
PCC/CC1 |
CP-OFDM 16QAM |
Outer_Full |
|||
|
SCC/CC2 |
CP-OFDM 16QAM |
Outer_Full |
||||
|
3 |
PCC/CC1 |
CP-OFDM 64QAM |
Outer_Full |
|||
|
SCC/CC2 |
CP-OFDM 64QAM |
Outer_Full |
||||
|
Default Test Settings for a CA_nXD Configuration (Cumulative aggregated BWchannel < 400MHz) |
||||||
|
1 |
PCC/CC1 |
100MHz |
Default |
N/A for this |
DFT-s-OFDM Pi/2 BPSK |
Outer_Full |
|
SCC/CC2 |
200MHz |
test |
DFT-s-OFDM Pi/2 BPSK |
Outer_Full |
||
|
2 |
PCC/CC1 |
100MHz |
CP-OFDM 16QAM |
Outer_Full |
||
|
SCC/CC2 |
200MHz |
CP-OFDM 16QAM |
Outer_Full |
|||
|
3 |
PCC/CC1 |
100MHz |
CP-OFDM 64QAM |
Outer_Full |
||
|
SCC/CC2 |
200MHz |
CP-OFDM 64QAM |
Outer_Full |
|||
|
Default Test Settings for a CA_nX(D-G)_UL_nXD, CA_nX(D-G)_UL_nXG, CA_nX(D-O)_UL_nXD, CA_nX(D-O)_UL_nXO Configuration (800MHz <= Cumulative aggregated BWchannel <= 1400MHz) |
||||||
|
1 |
PCC/CC1 |
Default |
Default |
N/A for this |
DFT-s-OFDM Pi/2 BPSK |
Outer_Full |
|
SCC1/CC2 |
test |
DFT-s-OFDM Pi/2 BPSK |
Outer_Full |
|||
|
Wgap |
N/A |
N/A |
||||
|
SCC2/CC3 |
N/A |
N/A |
||||
|
SCC3/CC4 |
N/A |
N/A |
||||
|
2 |
PCC/CC1 |
DFT-s-OFDM QPSK |
Outer_Full |
|||
|
SCC1/CC2 |
DFT-s-OFDM QPSK |
Outer_Full |
||||
|
Wgap |
N/A |
N/A |
||||
|
SCC2/CC3 |
N/A |
N/A |
||||
|
SCC3/CC4 |
N/A |
N/A |
||||
|
3 |
PCC/CC1 |
DFT-s-OFDM 16QAM |
Outer_Full |
|||
|
SCC1/CC2 |
DFT-s-OFDM 16QAM |
Outer_Full |
||||
|
Wgap |
N/A |
N/A |
||||
|
SCC2/CC3 |
N/A |
N/A |
||||
|
SCC3/CC4 |
N/A |
N/A |
||||
|
4 |
PCC/CC1 |
CP-OFDM 16QAM |
Outer_Full |
|||
|
SCC1/CC2 |
CP-OFDM 16QAM |
Outer_Full |
||||
|
Wgap |
N/A |
N/A |
||||
|
SCC2/CC3 |
N/A |
N/A |
||||
|
SCC3/CC4 |
N/A |
N/A |
||||
|
5 |
PCC/CC1 |
CP-OFDM 64QAM |
Outer_Full |
|||
|
SCC1/CC2 |
CP-OFDM 64QAM |
Outer_Full |
||||
|
Wgap |
N/A |
N/A |
||||
|
SCC2/CC3 |
N/A |
N/A |
||||
|
SCC3/CC4 |
N/A |
N/A |
||||
|
Default Test Settings for a CA_nX(D-H)_UL_nXD, CA_nX(D-P)_UL_nXD, CA_nX(E-O)_UL_nXO Configuration (800MHz <= Cumulative aggregated BWchannel <= 1400MHz) |
||||||
|
1 |
PCC/CC1 |
Default |
Default |
N/A for this |
DFT-s-OFDM Pi/2 BPSK |
Outer_Full |
|
SCC1/CC2 |
test |
DFT-s-OFDM Pi/2 BPSK |
Outer_Full |
|||
|
Wgap |
N/A |
N/A |
||||
|
SCC2/CC3 |
N/A |
N/A |
||||
|
SCC3/CC4 |
N/A |
N/A |
||||
|
SCC4/CC5 |
N/A |
N/A |
||||
|
2 |
PCC/CC1 |
DFT-s-OFDM QPSK |
Outer_Full |
|||
|
SCC1/CC2 |
DFT-s-OFDM QPSK |
Outer_Full |
||||
|
Wgap |
N/A |
N/A |
||||
|
SCC2/CC3 |
N/A |
N/A |
||||
|
SCC3/CC4 |
N/A |
N/A |
||||
|
SCC4/CC5 |
N/A |
N/A |
||||
|
3 |
PCC/CC1 |
DFT-s-OFDM 16QAM |
Outer_Full |
|||
|
SCC1/CC2 |
DFT-s-OFDM 16QAM |
Outer_Full |
||||
|
Wgap |
N/A |
N/A |
||||
|
SCC2/CC3 |
N/A |
N/A |
||||
|
SCC3/CC4 |
N/A |
N/A |
||||
|
SCC4/CC5 |
N/A |
N/A |
||||
|
4 |
PCC/CC1 |
CP-OFDM 16QAM |
Outer_Full |
|||
|
SCC1/CC2 |
CP-OFDM 16QAM |
Outer_Full |
||||
|
Wgap |
N/A |
N/A |
||||
|
SCC2/CC3 |
N/A |
N/A |
||||
|
SCC3/CC4 |
N/A |
N/A |
||||
|
SCC4/CC5 |
N/A |
N/A |
||||
|
5 |
PCC/CC1 |
CP-OFDM 64QAM |
Outer_Full |
|||
|
SCC1/CC2 |
CP-OFDM 64QAM |
Outer_Full |
||||
|
Wgap |
N/A |
N/A |
||||
|
SCC2/CC3 |
N/A |
N/A |
||||
|
SCC3/CC4 |
N/A |
N/A |
||||
|
SCC4/CC5 |
N/A |
N/A |
||||
|
Default Test Settings for a CA_nX(D-I)_UL_nXD, CA_nX(D-Q)_UL_nXD, CA_nX(G-I)_UL_nXG Configuration (800MHz <= Cumulative aggregated BWchannel <= 1400MHz) |
||||||
|
1 |
PCC/CC1 |
Default |
Default |
N/A for this |
DFT-s-OFDM Pi/2 BPSK |
Outer_Full |
|
SCC1/CC2 |
test |
DFT-s-OFDM Pi/2 BPSK |
Outer_Full |
|||
|
Wgap |
N/A |
N/A |
||||
|
SCC2/CC3 |
N/A |
N/A |
||||
|
SCC3/CC4 |
N/A |
N/A |
||||
|
SCC4/CC5 |
N/A |
N/A |
||||
|
SCC5/CC6 |
N/A |
N/A |
||||
|
2 |
PCC/CC1 |
DFT-s-OFDM QPSK |
Outer_Full |
|||
|
SCC1/CC2 |
DFT-s-OFDM QPSK |
Outer_Full |
||||
|
Wgap |
N/A |
N/A |
||||
|
SCC2/CC3 |
N/A |
N/A |
||||
|
SCC3/CC4 |
N/A |
N/A |
||||
|
SCC4/CC5 |
N/A |
N/A |
||||
|
SCC5/CC6 |
N/A |
N/A |
||||
|
3 |
PCC/CC1 |
DFT-s-OFDM 16QAM |
Outer_Full |
|||
|
SCC1/CC2 |
DFT-s-OFDM 16QAM |
Outer_Full |
||||
|
Wgap |
N/A |
N/A |
||||
|
SCC2/CC3 |
N/A |
N/A |
||||
|
SCC3/CC4 |
N/A |
N/A |
||||
|
SCC4/CC5 |
N/A |
N/A |
||||
|
SCC5/CC6 |
N/A |
N/A |
||||
|
4 |
PCC/CC1 |
CP-OFDM 16QAM |
Outer_Full |
|||
|
SCC1/CC2 |
CP-OFDM 16QAM |
Outer_Full |
||||
|
Wgap |
N/A |
N/A |
||||
|
SCC2/CC3 |
N/A |
N/A |
||||
|
SCC3/CC4 |
N/A |
N/A |
||||
|
SCC4/CC5 |
N/A |
N/A |
||||
|
SCC5/CC6 |
N/A |
N/A |
||||
|
5 |
PCC/CC1 |
CP-OFDM 64QAM |
Outer_Full |
|||
|
SCC1/CC2 |
CP-OFDM 64QAM |
Outer_Full |
||||
|
Wgap |
N/A |
N/A |
||||
|
SCC2/CC3 |
N/A |
N/A |
||||
|
SCC3/CC4 |
N/A |
N/A |
||||
|
SCC4/CC5 |
N/A |
N/A |
||||
|
SCC5/CC6 |
N/A |
N/A |
||||
|
Default Test Settings for a CA_nX(D-G)_UL_nXD, CA_nX(D-O)_UL_nXD Configuration (400MHz <= Cumulative aggregated BWchannel <800MHz) |
||||||
|
1 |
PCC/CC1 |
200MHz |
Default |
N/A for this |
DFT-s-OFDM Pi/2 BPSK |
Outer_Full |
|
SCC1/CC2 |
200MHz |
test |
DFT-s-OFDM Pi/2 BPSK |
Outer_Full |
||
|
Wgap |
190MHz |
N/A |
N/A |
|||
|
SCC2/CC3 |
100MHz |
N/A |
N/A |
|||
|
SCC3/CC4 |
100MHz |
N/A |
N/A |
|||
|
2 |
PCC/CC1 |
200MHz |
CP-OFDM 16QAM |
Outer_Full |
||
|
SCC1/CC2 |
200MHz |
CP-OFDM 16QAM |
Outer_Full |
|||
|
Wgap |
190MHz |
N/A |
N/A |
|||
|
SCC2/CC3 |
100MHz |
N/A |
N/A |
|||
|
SCC3/CC4 |
100MHz |
N/A |
N/A |
|||
|
3 |
PCC/CC1 |
200MHz |
CP-OFDM 64QAM |
Outer_Full |
||
|
SCC1/CC2 |
200MHz |
CP-OFDM 64QAM |
Outer_Full |
|||
|
Wgap |
190MHz |
N/A |
N/A |
|||
|
SCC2/CC3 |
100MHz |
N/A |
N/A |
|||
|
SCC3/CC4 |
100MHz |
N/A |
N/A |
|||
|
Default Test Settings for a CA_nX(D-G)_UL_nXG, CA_nX(D-O)_UL_nXO Configuration (400MHz <= Cumulative aggregated BWchannel <800MHz) |
||||||
|
1 |
PCC/CC1 |
100MHz |
Default |
N/A for this |
DFT-s-OFDM Pi/2 BPSK |
Outer_Full |
|
SCC1/CC2 |
100MHz |
test |
DFT-s-OFDM Pi/2 BPSK |
Outer_Full |
||
|
Wgap |
190MHz |
N/A |
N/A |
|||
|
SCC2/CC3 |
200MHz |
N/A |
N/A |
|||
|
SCC3/CC4 |
200MHz |
N/A |
N/A |
|||
|
2 |
PCC/CC1 |
100MHz |
CP-OFDM 16QAM |
Outer_Full |
||
|
SCC1/CC2 |
100MHz |
CP-OFDM 16QAM |
Outer_Full |
|||
|
Wgap |
190MHz |
N/A |
N/A |
|||
|
SCC2/CC3 |
200MHz |
N/A |
N/A |
|||
|
SCC3/CC4 |
200MHz |
N/A |
N/A |
|||
|
3 |
PCC/CC1 |
100MHz |
CP-OFDM 64QAM |
Outer_Full |
||
|
SCC1/CC2 |
100MHz |
CP-OFDM 64QAM |
Outer_Full |
|||
|
Wgap |
190MHz |
N/A |
N/A |
|||
|
SCC2/CC3 |
200MHz |
N/A |
N/A |
|||
|
SCC3/CC4 |
200MHz |
N/A |
N/A |
|||
|
Default Test Settings for a CA_nX(D-H)_UL_nXD, CA_nX(D-P)_UL_nXD, Configuration (400MHz <= Cumulative aggregated BWchannel < 800MHz) |
||||||
|
1 |
PCC/CC1 |
200MHz |
Default |
N/A for this |
DFT-s-OFDM Pi/2 BPSK |
Outer_Full |
|
SCC1/CC2 |
200MHz |
test |
DFT-s-OFDM Pi/2 BPSK |
Outer_Full |
||
|
Wgap |
90MHz |
N/A |
N/A |
|||
|
SCC2/CC3 |
100MHz |
N/A |
N/A |
|||
|
SCC3/CC4 |
100MHz |
N/A |
N/A |
|||
|
SCC4/CC5 |
100MHz |
N/A |
N/A |
|||
|
2 |
PCC/CC1 |
200MHz |
CP-OFDM 16QAM |
Outer_Full |
||
|
SCC1/CC2 |
200MHz |
CP-OFDM 16QAM |
Outer_Full |
|||
|
Wgap |
90MHz |
N/A |
N/A |
|||
|
SCC2/CC3 |
100MHz |
N/A |
N/A |
|||
|
SCC3/CC4 |
100MHz |
N/A |
N/A |
|||
|
SCC4/CC5 |
100MHz |
N/A |
N/A |
|||
|
3 |
PCC/CC1 |
200MHz |
CP-OFDM 64QAM |
Outer_Full |
||
|
SCC1/CC2 |
200MHz |
CP-OFDM 64QAM |
Outer_Full |
|||
|
Wgap |
90MHz |
N/A |
N/A |
|||
|
SCC2/CC3 |
100MHz |
N/A |
N/A |
|||
|
SCC3/CC4 |
100MHz |
N/A |
N/A |
|||
|
SCC4/CC5 |
100MHz |
N/A |
N/A |
|||
|
Default Test Settings for a CA_nX(O-E)_UL_nXO Configuration (400MHz <= Cumulative aggregated BWchannel < 800MHz) |
||||||
|
1 |
PCC/CC1 |
100MHz |
Default |
N/A for this |
DFT-s-OFDM Pi/2 BPSK |
Outer_Full |
|
SCC1/CC2 |
100MHz |
test |
DFT-s-OFDM Pi/2 BPSK |
Outer_Full |
||
|
Wgap |
90MHz |
N/A |
N/A |
|||
|
SCC2/CC3 |
100MHz |
N/A |
N/A |
|||
|
SCC3/CC4 |
200MHz |
N/A |
N/A |
|||
|
SCC4/CC5 |
200MHz |
N/A |
N/A |
|||
|
2 |
PCC/CC1 |
100MHz |
CP-OFDM 16QAM |
Outer_Full |
||
|
SCC1/CC2 |
100MHz |
CP-OFDM 16QAM |
Outer_Full |
|||
|
Wgap |
90MHz |
N/A |
N/A |
|||
|
SCC2/CC3 |
100MHz |
N/A |
N/A |
|||
|
SCC3/CC4 |
200MHz |
N/A |
N/A |
|||
|
SCC4/CC5 |
200MHz |
N/A |
N/A |
|||
|
3 |
PCC/CC1 |
100MHz |
CP-OFDM 64QAM |
Outer_Full |
||
|
SCC1/CC2 |
100MHz |
CP-OFDM 64QAM |
Outer_Full |
|||
|
Wgap |
90MHz |
N/A |
N/A |
|||
|
SCC2/CC3 |
100MHz |
N/A |
N/A |
|||
|
SCC3/CC4 |
200MHz |
N/A |
N/A |
|||
|
SCC4/CC5 |
200MHz |
N/A |
N/A |
|||
|
Default Test Settings for a CA_nX(D-I)_UL_nXD, CA_nX(D-Q)_UL_nXD Configuration (400MHz <= Cumulative aggregated BWchannel < 800MHz) |
||||||
|
1 |
PCC/CC1 |
100MHz |
Default |
N/A for this |
DFT-s-OFDM Pi/2 BPSK |
Outer_Full |
|
SCC1/CC2 |
200MHz |
test |
DFT-s-OFDM Pi/2 BPSK |
Outer_Full |
||
|
Wgap |
90MHz |
N/A |
N/A |
|||
|
SCC2/CC3 |
100MHz |
N/A |
N/A |
|||
|
SCC3/CC4 |
100MHz |
N/A |
N/A |
|||
|
SCC4/CC5 |
100MHz |
N/A |
N/A |
|||
|
SCC5/CC6 |
100MHz |
N/A |
N/A |
|||
|
2 |
PCC/CC1 |
100MHz |
CP-OFDM 16QAM |
Outer_Full |
||
|
SCC1/CC2 |
200MHz |
CP-OFDM 16QAM |
Outer_Full |
|||
|
Wgap |
90MHz |
N/A |
N/A |
|||
|
SCC2/CC3 |
100MHz |
N/A |
N/A |
|||
|
SCC3/CC4 |
100MHz |
N/A |
N/A |
|||
|
SCC4/CC5 |
100MHz |
N/A |
N/A |
|||
|
SCC5/CC6 |
100MHz |
N/A |
N/A |
|||
|
3 |
PCC/CC1 |
100MHz |
CP-OFDM 64QAM |
Outer_Full |
||
|
SCC1/CC2 |
200MHz |
CP-OFDM 64QAM |
Outer_Full |
|||
|
Wgap |
90MHz |
N/A |
N/A |
|||
|
SCC2/CC3 |
100MHz |
N/A |
N/A |
|||
|
SCC3/CC4 |
100MHz |
N/A |
N/A |
|||
|
SCC4/CC5 |
100MHz |
N/A |
N/A |
|||
|
SCC5/CC6 |
100MHz |
N/A |
N/A |
|||
|
Default Test Settings for a CA_nX(G-I)_UL_nXG Configuration (400MHz <= Cumulative aggregated BWchannel < 800MHz) |
||||||
|
1 |
PCC/CC1 |
100MHz |
Default |
N/A for this |
DFT-s-OFDM Pi/2 BPSK |
Outer_Full |
|
SCC1/CC2 |
100MHz |
test |
DFT-s-OFDM Pi/2 BPSK |
Outer_Full |
||
|
Wgap |
190MHz |
N/A |
N/A |
|||
|
SCC2/CC3 |
100MHz |
N/A |
N/A |
|||
|
SCC3/CC4 |
100MHz |
N/A |
N/A |
|||
|
SCC4/CC5 |
100MHz |
N/A |
N/A |
|||
|
SCC5/CC6 |
100MHz |
N/A |
N/A |
|||
|
2 |
PCC/CC1 |
100MHz |
CP-OFDM 16QAM |
Outer_Full |
||
|
SCC1/CC2 |
100MHz |
CP-OFDM 16QAM |
Outer_Full |
|||
|
Wgap |
190MHz |
N/A |
N/A |
|||
|
SCC2/CC3 |
100MHz |
N/A |
N/A |
|||
|
SCC3/CC4 |
100MHz |
N/A |
N/A |
|||
|
SCC4/CC5 |
100MHz |
N/A |
N/A |
|||
|
SCC5/CC6 |
100MHz |
N/A |
N/A |
|||
|
3 |
PCC/CC1 |
100MHz |
CP-OFDM 64QAM |
Outer_Full |
||
|
SCC1/CC2 |
100MHz |
CP-OFDM 64QAM |
Outer_Full |
|||
|
Wgap |
190MHz |
N/A |
N/A |
|||
|
SCC2/CC3 |
100MHz |
N/A |
N/A |
|||
|
SCC3/CC4 |
100MHz |
N/A |
N/A |
|||
|
SCC4/CC5 |
100MHz |
N/A |
N/A |
|||
|
SCC5/CC6 |
100MHz |
N/A |
N/A |
|||
|
Default Test Settings for a CA_nX(D-O)_UL_nXD Configuration (Cumulative aggregated BWchannel <400MHz) |
||||||
|
1 |
PCC/CC1 |
50MHz |
Default |
N/A for this |
DFT-s-OFDM Pi/2 BPSK |
Outer_Full |
|
SCC1/CC2 |
200MHz |
test |
DFT-s-OFDM Pi/2 BPSK |
Outer_Full |
||
|
Wgap |
40MHz |
N/A |
N/A |
|||
|
SCC2/CC3 |
50MHz |
N/A |
N/A |
|||
|
SCC3/CC4 |
50MHz |
N/A |
N/A |
|||
|
2 |
PCC/CC1 |
50MHz |
CP-OFDM 16QAM |
Outer_Full |
||
|
SCC1/CC2 |
200MHz |
CP-OFDM 16QAM |
Outer_Full |
|||
|
Wgap |
40MHz |
N/A |
N/A |
|||
|
SCC2/CC3 |
50MHz |
N/A |
N/A |
|||
|
SCC3/CC4 |
50MHz |
N/A |
N/A |
|||
|
3 |
PCC/CC1 |
50MHz |
CP-OFDM 64QAM |
Outer_Full |
||
|
SCC1/CC2 |
200MHz |
CP-OFDM 64QAM |
Outer_Full |
|||
|
Wgap |
40MHz |
N/A |
N/A |
|||
|
SCC2/CC3 |
50MHz |
N/A |
N/A |
|||
|
SCC3/CC4 |
50MHz |
N/A |
N/A |
|||
|
Default Test Settings for a CA_nX(D-O)_UL_nXO Configuration (Cumulative aggregated BWchannel <400MHz) |
||||||
|
1 |
PCC/CC1 |
50MHz |
Default |
N/A for this |
N/A |
N/A |
|
SCC1/CC2 |
200MHz |
test |
N/A |
N/A |
||
|
Wgap |
40MHz |
N/A |
N/A |
|||
|
SCC2/CC3 |
50MHz |
DFT-s-OFDM Pi/2 BPSK |
Outer_Full |
|||
|
SCC3/CC4 |
50MHz |
DFT-s-OFDM Pi/2 BPSK |
Outer_Full |
|||
|
2 |
PCC/CC1 |
50MHz |
N/A |
N/A |
||
|
SCC1/CC2 |
200MHz |
N/A |
N/A |
|||
|
Wgap |
40MHz |
N/A |
N/A |
|||
|
SCC2/CC3 |
50MHz |
CP-OFDM 16QAM |
Outer_Full |
|||
|
SCC3/CC4 |
50MHz |
CP-OFDM 16QAM |
Outer_Full |
|||
|
3 |
PCC/CC1 |
50MHz |
N/A |
N/A |
||
|
SCC1/CC2 |
200MHz |
N/A |
N/A |
|||
|
Wgap |
40MHz |
N/A |
N/A |
|||
|
SCC2/CC3 |
50MHz |
CP-OFDM 64QAM |
Outer_Full |
|||
|
SCC3/CC4 |
50MHz |
CP-OFDM 64QAM |
Outer_Full |
|||
|
NOTE 1: The specific configuration of each RB allocation is defined in Table 6.1-2. NOTE 2: PCC/CCi and SCC/CCj means PCC is on component carrier CCi and SCC is on component carrier CCj, with CCi or CCj frequencies defined in TS38.508-1 [10]. |
||||||
Table 6.2A.2.1.4.1-4: Intra-band Contiguous UL CA Test Configuration Table (Power Class 1, Non-contiguous allocation)
|
Default Conditions |
||||||
|
Test Environment as specified in TS 38.508-1 [10] subclause 4.1 |
Normal |
|||||
|
Test Frequencies as specified in TS 38.508-1 [10] subclause 4.3.1.2.3 for different CA bandwidth classes |
For intra-band contiguous CA: Mid range. For intra-band non-contiguous CA: Lowest range with Max Wgap, Highest range with Max Wgap. |
|||||
|
Test CC Combination setting (aggregated BW of the CA configuration) as specified in Table 5.5A.1-1, 5.5A.2-1 and 5.5A.2-2 for the CA Configuration across bandwidth combination sets supported by the UE |
Highest aggregated channel bandwidth of the CA configuration |
|||||
|
Test SCS as specified in Table 5.3.5-1 |
120 kHz |
|||||
|
Test Parameters |
||||||
|
Test ID |
CC & Mapping (NOTE 2) |
ChBw(MHz) |
Test frequency |
DL RB allocation |
UL Modulation |
UL RB allocation |
|
Default Test Settings for a CA_nXB, CA_nXD, CA_XG, CA_nXO Configuration |
||||||
|
1 |
PCC/CC1 |
Default |
Default |
N/A for this |
CP-OFDM 64QAM |
Outer_1RB_Left |
|
SCC/CC2 |
test |
CP-OFDM 64QAM |
Outer_1RB_Right |
|||
|
2 |
PCC/CC1 |
DFT-s-OFDM Pi/2 BPSK |
[Outer_0.9_Left] |
|||
|
SCC/CC2 |
DFT-s-OFDM Pi/2 BPSK |
[Outer_0.9_Right] |
||||
|
3 |
PCC/CC1 |
DFT-s-OFDM Pi/2 QPSK |
[Outer_0.9_Left] |
|||
|
SCC/CC2 |
DFT-s-OFDM Pi/2 QPSK |
[Outer_0.9_Right] |
||||
|
Default Test Settings for a CA_nX(D-G), CA_nX(D-O) Configuration |
||||||
|
1 |
PCC/CC1 |
Default |
Default |
N/A for this |
DFT-s-OFDM QPSK |
Outer_1RB_Left |
|
SCC1/CC2 |
test |
DFT-s-OFDM QPSK |
Outer_1RB_Right |
|||
|
Wgap |
N/A |
N/A |
||||
|
SCC2/CC3 |
N/A |
N/A |
||||
|
SCC3/CC4 |
N/A |
N/A |
||||
|
2 |
PCC/CC1 |
DFT-s-OFDM Pi/2 BPSK |
[Outer_0.9_Left] |
|||
|
SCC1/CC2 |
DFT-s-OFDM Pi/2 BPSK |
[Outer_0.9_Right] |
||||
|
Wgap |
N/A |
N/A |
||||
|
SCC2/CC3 |
N/A |
N/A |
||||
|
SCC3/CC4 |
N/A |
N/A |
||||
|
3 |
PCC/CC1 |
DFT-s-OFDM Pi/2 QPSK |
[Outer_0.9_Left] |
|||
|
SCC1/CC2 |
DFT-s-OFDM Pi/2 QPSK |
[Outer_0.9_Right] |
||||
|
Wgap |
N/A |
N/A |
||||
|
SCC2/CC3 |
N/A |
N/A |
||||
|
SCC3/CC4 |
N/A |
N/A |
||||
|
NOTE 1: The specific configuration of each RB allocation is defined in Table 6.1-2. NOTE 2: PCC/CCi and SCC/CCj means PCC is on component carrier CCi and SCC is on component carrier CCj, with CCi or CCj frequencies defined in TS38.508-1 [10]. |
||||||
Table 6.2A.2.1.4.1-5: Intra-band Contiguous UL CA Test Configuration Table (Power Class 2, 3 and 4, single CC MPR requirement)
|
Default Conditions |
||||||
|
Test Environment as specified in TS 38.508-1 [10] subclause 4.1 |
Normal |
|||||
|
Test Frequencies as specified in TS 38.508-1 [10] subclause 4.3.1.2.3 for different CA bandwidth classes |
Lowest range, Highest range |
|||||
|
Test CC Combination setting (aggregated BW of the CA configuration) as specified in Table 5.5A.1-1, 5.5A.2-1 and 5.5A.2-2 for the CA Configuration across bandwidth combination sets supported by the UE |
Highest aggregated channel bandwidth of the CA configuration |
|||||
|
Test SCS as specified in Table 5.3.5-1 |
120 kHz |
|||||
|
Test Parameters |
||||||
|
Test ID |
CC & Mapping (NOTE 2) |
ChBw(MHz) |
Test frequency |
DL RB allocation |
UL Modulation |
UL RB allocation |
|
Default Test Settings for a CA_nXG, CA_nXO Configuration (Cumulative aggregated BWchannel <= 200MHz) |
||||||
|
1 |
PCC/CC1 |
Default |
Default |
N/A for this |
DFT-s-OFDM QPSK |
Inner_Full |
|
SCC/CC2 |
test |
– |
– |
|||
|
2 |
PCC/CC1 |
DFT-s-OFDM QPSK |
Outer_Full |
|||
|
SCC/CC2 |
– |
– |
||||
|
Default Test Settings for a CA_nXD Configuration (Cumulative aggregated BWchannel <= 400MHz) |
||||||
|
1 |
PCC/CC1 |
Default |
Default |
N/A for this |
DFT-s-OFDM QPSK |
Inner_Full |
|
SCC/CC2 |
test |
– |
– |
|||
|
2 |
PCC/CC1 |
DFT-s-OFDM QPSK |
Outer_Full |
|||
|
SCC/CC2 |
– |
– |
||||
|
NOTE 1: The specific configuration of each RB allocation is defined in Table 6.1-1. NOTE 2: PCC/CCi and SCC/CCj means PCC is on component carrier CCi and SCC is on component carrier CCj, with CCi or CCj frequencies defined in TS38.508-1 [10]. |
||||||
Table 6.2A.2.1.4.1-6: Intra-band Contiguous UL CA Test Configuration Table (Power Class 2, 3 and 4, MPRC_CA)
|
Default Conditions |
|||||||||||||||||||||
|
Test Environment as specified in TS 38.508-1 [10] subclause 4.1 |
Normal |
||||||||||||||||||||
|
Test Frequencies as specified in TS 38.508-1 [10] subclause 4.3.1.2.3 for different CA bandwidth classes |
For intra-band contiguous CA: Mid range. For intra-band non-contiguous CA: Lowest range with Max Wgap, Highest range with Max Wgap. |
||||||||||||||||||||
|
Test CC Combination setting (aggregated BW of the CA configuration) as specified in Table 5.5A.1-1, 5.5A.2-1 and 5.5A.2-2 for the CA Configuration across bandwidth combination sets supported by the UE |
Highest aggregated channel bandwidth of the CA configuration |
||||||||||||||||||||
|
Test SCS as specified in Table 5.3.5-1 |
120 kHz |
||||||||||||||||||||
|
Test Parameters |
|||||||||||||||||||||
|
Test ID |
CC & Mapping (NOTE 2) |
ChBw(MHz) |
Test frequency |
DL RB allocation |
UL Modulation |
UL RB allocation |
|||||||||||||||
|
Default Test Settings for a CA_nXB, nXC_UL_nXB Configuration (800MHz <= Cumulative aggregated BWchannel <= 1400MHz) |
|||||||||||||||||||||
|
1 |
PCC/CC1 |
Default |
Default |
N/A for this |
DFT-s-OFDM QPSK |
Outer_Full |
|||||||||||||||
|
SCC/CC2 |
test |
DFT-s-OFDM QPSK |
Outer_Full |
||||||||||||||||||
|
2 |
PCC/CC1 |
DFT-s-OFDM 16QAM |
Outer_Full |
||||||||||||||||||
|
SCC/CC2 |
DFT-s-OFDM 16QAM |
Outer_Full |
|||||||||||||||||||
|
3 |
PCC/CC1 |
CP-OFDM QPSK |
Outer_Full |
||||||||||||||||||
|
SCC/CC2 |
CP-OFDM QPSK |
Outer_Full |
|||||||||||||||||||
|
4 |
PCC/CC1 |
CP-OFDM 16QAM |
Outer_Full |
||||||||||||||||||
|
SCC/CC2 |
CP-OFDM 16QAM |
Outer_Full |
|||||||||||||||||||
|
5 |
PCC/CC1 |
CP-OFDM 64QAM |
Outer_Full |
||||||||||||||||||
|
SCC/CC2 |
CP-OFDM 64QAM |
Outer_Full |
|||||||||||||||||||
|
Default Test Settings for a CA_nXD Configuration (400MHz <= Cumulative aggregated BWchannel < 800MHz) |
|||||||||||||||||||||
|
1 |
PCC/CC1 |
Default |
Default |
N/A for this |
DFT-s-OFDM QPSK |
Outer_Full |
|||||||||||||||
|
SCC/CC2 |
test |
DFT-s-OFDM QPSK |
Outer_Full |
||||||||||||||||||
|
2 |
PCC/CC1 |
CP-OFDM QPSK |
Outer_Full |
||||||||||||||||||
|
SCC/CC2 |
CP-OFDM QPSK |
Outer_Full |
|||||||||||||||||||
|
3 |
PCC/CC1 |
CP-OFDM 16QAM |
Outer_Full |
||||||||||||||||||
|
SCC/CC2 |
CP-OFDM 16QAM |
Outer_Full |
|||||||||||||||||||
|
4 |
PCC/CC1 |
CP-OFDM 64QAM |
Outer_Full |
||||||||||||||||||
|
SCC/CC2 |
CP-OFDM 64QAM |
Outer_Full |
|||||||||||||||||||
|
Default Test Settings for a CA_nXB Configuration (400MHz <= Cumulative aggregated BWchannel < 800MHz) |
|||||||||||||||||||||
|
1 |
PCC/CC1 |
200MHz |
Default |
N/A for this |
DFT-s-OFDM QPSK |
Outer_Full |
|||||||||||||||
|
SCC/CC2 |
400MHz |
test |
DFT-s-OFDM QPSK |
Outer_Full |
|||||||||||||||||
|
2 |
PCC/CC1 |
200MHz |
CP-OFDM QPSK |
Outer_Full |
|||||||||||||||||
|
SCC/CC2 |
400MHz |
CP-OFDM QPSK |
Outer_Full |
||||||||||||||||||
|
3 |
PCC/CC1 |
200MHz |
CP-OFDM 16QAM |
Outer_Full |
|||||||||||||||||
|
SCC/CC2 |
400MHz |
CP-OFDM 16QAM |
Outer_Full |
||||||||||||||||||
|
4 |
PCC/CC1 |
200MHz |
CP-OFDM 64QAM |
Outer_Full |
|||||||||||||||||
|
SCC/CC2 |
400MHz |
CP-OFDM 64QAM |
Outer_Full |
||||||||||||||||||
|
Default Test Settings for a CA_nXG, CA_nXO Configuration (Cumulative aggregated BWchannel < 400MHz) |
|||||||||||||||||||||
|
1 |
PCC/CC1 |
Default |
Default |
N/A for this |
CP-OFDM QPSK |
Outer_Full |
|||||||||||||||
|
SCC/CC2 |
test |
CP-OFDM QPSK |
Outer_Full |
||||||||||||||||||
|
2 |
PCC/CC1 |
CP-OFDM 16QAM |
Outer_Full |
||||||||||||||||||
|
SCC/CC2 |
CP-OFDM 16QAM |
Outer_Full |
|||||||||||||||||||
|
3 |
PCC/CC1 |
CP-OFDM 64QAM |
Outer_Full |
||||||||||||||||||
|
SCC/CC2 |
CP-OFDM 64QAM |
Outer_Full |
|||||||||||||||||||
|
Default Test Settings for a CA_nXD Configuration (Cumulative aggregated BWchannel < 400MHz) |
|||||||||||||||||||||
|
1 |
PCC/CC1 |
100MHz |
Default |
N/A for this |
CP-OFDM QPSK |
Outer_Full |
|||||||||||||||
|
SCC/CC2 |
200MHz |
test |
CP-OFDM QPSK |
Outer_Full |
|||||||||||||||||
|
2 |
PCC/CC1 |
100MHz |
CP-OFDM 16QAM |
Outer_Full |
|||||||||||||||||
|
SCC/CC2 |
200MHz |
CP-OFDM 16QAM |
Outer_Full |
||||||||||||||||||
|
3 |
PCC/CC1 |
100MHz |
CP-OFDM 64QAM |
Outer_Full |
|||||||||||||||||
|
SCC/CC2 |
200MHz |
CP-OFDM 64QAM |
Outer_Full |
||||||||||||||||||
|
Default Test Settings for a CA_nX(D-G) )_UL_nXD, CA_nX(D-G)_UL_nXG, CA_nX(D-O)_UL_nXD, CA_nX(D-O)_UL_nXO Configuration (800MHz <= Cumulative aggregated BWchannel <= 1400MHz) |
|||||||||||||||||||||
|
1 |
PCC/CC1 |
Default |
Default |
N/A for this |
DFT-s-OFDM QPSK |
Outer_Full |
|||||||||||||||
|
SCC1/CC2 |
test |
DFT-s-OFDM QPSK |
Outer_Full |
||||||||||||||||||
|
Wgap |
N/A |
N/A |
|||||||||||||||||||
|
SCC2/CC3 |
N/A |
N/A |
|||||||||||||||||||
|
SCC3/CC4 |
N/A |
N/A |
|||||||||||||||||||
|
2 |
PCC/CC1 |
DFT-s-OFDM 16QAM |
Outer_Full |
||||||||||||||||||
|
SCC1/CC2 |
DFT-s-OFDM 16QAM |
Outer_Full |
|||||||||||||||||||
|
Wgap |
N/A |
N/A |
|||||||||||||||||||
|
SCC2/CC3 |
N/A |
N/A |
|||||||||||||||||||
|
SCC3/CC4 |
N/A |
N/A |
|||||||||||||||||||
|
3 |
PCC/CC1 |
CP-OFDM QPSK |
Outer_Full |
||||||||||||||||||
|
SCC1/CC2 |
CP-OFDM QPSK |
Outer_Full |
|||||||||||||||||||
|
Wgap |
N/A |
N/A |
|||||||||||||||||||
|
SCC2/CC3 |
N/A |
N/A |
|||||||||||||||||||
|
SCC3/CC4 |
N/A |
N/A |
|||||||||||||||||||
|
4 |
PCC/CC1 |
CP-OFDM 16QAM |
Outer_Full |
||||||||||||||||||
|
SCC1/CC2 |
CP-OFDM 16QAM |
Outer_Full |
|||||||||||||||||||
|
Wgap |
N/A |
N/A |
|||||||||||||||||||
|
SCC2/CC3 |
N/A |
N/A |
|||||||||||||||||||
|
SCC3/CC4 |
N/A |
N/A |
|||||||||||||||||||
|
5 |
PCC/CC1 |
CP-OFDM 64QAM |
Outer_Full |
||||||||||||||||||
|
SCC1/CC2 |
CP-OFDM 64QAM |
Outer_Full |
|||||||||||||||||||
|
Wgap |
N/A |
N/A |
|||||||||||||||||||
|
SCC2/CC3 |
N/A |
N/A |
|||||||||||||||||||
|
SCC3/CC4 |
N/A |
N/A |
|||||||||||||||||||
|
Default Test Settings for a CA_nX(D-H)_UL_nXD, CA_nX(D-P)_UL_nXD, CA_nX(E-O)_UL_nXO Configuration (800MHz <= Cumulative aggregated BWchannel <= 1400MHz) |
|||||||||||||||||||||
|
1 |
PCC/CC1 |
Default |
Default |
N/A for this |
DFT-s-OFDM QPSK |
Outer_Full |
|||||||||||||||
|
SCC1/CC2 |
test |
DFT-s-OFDM QPSK |
Outer_Full |
||||||||||||||||||
|
Wgap |
N/A |
N/A |
|||||||||||||||||||
|
SCC2/CC3 |
N/A |
N/A |
|||||||||||||||||||
|
SCC3/CC4 |
N/A |
N/A |
|||||||||||||||||||
|
SCC4/CC5 |
N/A |
N/A |
|||||||||||||||||||
|
2 |
PCC/CC1 |
DFT-s-OFDM 16QAM |
Outer_Full |
||||||||||||||||||
|
SCC1/CC2 |
DFT-s-OFDM 16QAM |
Outer_Full |
|||||||||||||||||||
|
Wgap |
N/A |
N/A |
|||||||||||||||||||
|
SCC2/CC3 |
N/A |
N/A |
|||||||||||||||||||
|
SCC3/CC4 |
N/A |
N/A |
|||||||||||||||||||
|
SCC4/CC5 |
N/A |
N/A |
|||||||||||||||||||
|
3 |
PCC/CC1 |
CP-OFDM QPSK |
Outer_Full |
||||||||||||||||||
|
SCC1/CC2 |
CP-OFDM QPSK |
Outer_Full |
|||||||||||||||||||
|
Wgap |
N/A |
N/A |
|||||||||||||||||||
|
SCC2/CC3 |
N/A |
N/A |
|||||||||||||||||||
|
SCC3/CC4 |
N/A |
N/A |
|||||||||||||||||||
|
SCC4/CC5 |
N/A |
N/A |
|||||||||||||||||||
|
4 |
PCC/CC1 |
CP-OFDM 16QAM |
Outer_Full |
||||||||||||||||||
|
SCC1/CC2 |
CP-OFDM 16QAM |
Outer_Full |
|||||||||||||||||||
|
Wgap |
N/A |
N/A |
|||||||||||||||||||
|
SCC2/CC3 |
N/A |
N/A |
|||||||||||||||||||
|
SCC3/CC4 |
N/A |
N/A |
|||||||||||||||||||
|
SCC4/CC5 |
N/A |
N/A |
|||||||||||||||||||
|
5 |
PCC/CC1 |
CP-OFDM 64QAM |
Outer_Full |
||||||||||||||||||
|
SCC1/CC2 |
CP-OFDM 64QAM |
Outer_Full |
|||||||||||||||||||
|
Wgap |
N/A |
N/A |
|||||||||||||||||||
|
SCC2/CC3 |
N/A |
N/A |
|||||||||||||||||||
|
SCC3/CC4 |
N/A |
N/A |
|||||||||||||||||||
|
SCC4/CC5 |
N/A |
N/A |
|||||||||||||||||||
|
Default Test Settings for a CA_nX(D-I)_UL_nXD, CA_nX(D-Q)_UL_nXD, CA_nX(G-I)_UL_nXG Configuration (800MHz <= Cumulative aggregated BWchannel <= 1400MHz) |
|||||||||||||||||||||
|
1 |
PCC/CC1 |
Default |
Default |
N/A for this |
DFT-s-OFDM QPSK |
Outer_Full |
|||||||||||||||
|
SCC1/CC2 |
test |
DFT-s-OFDM QPSK |
Outer_Full |
||||||||||||||||||
|
Wgap |
N/A |
N/A |
|||||||||||||||||||
|
SCC2/CC3 |
N/A |
N/A |
|||||||||||||||||||
|
SCC3/CC4 |
N/A |
N/A |
|||||||||||||||||||
|
SCC4/CC5 |
N/A |
N/A |
|||||||||||||||||||
|
SCC5/CC6 |
N/A |
N/A |
|||||||||||||||||||
|
2 |
PCC/CC1 |
DFT-s-OFDM 16QAM |
Outer_Full |
||||||||||||||||||
|
SCC1/CC2 |
DFT-s-OFDM 16QAM |
Outer_Full |
|||||||||||||||||||
|
Wgap |
N/A |
N/A |
|||||||||||||||||||
|
SCC2/CC3 |
N/A |
N/A |
|||||||||||||||||||
|
SCC3/CC4 |
N/A |
N/A |
|||||||||||||||||||
|
SCC4/CC5 |
N/A |
N/A |
|||||||||||||||||||
|
SCC5/CC6 |
N/A |
N/A |
|||||||||||||||||||
|
3 |
PCC/CC1 |
CP-OFDM QPSK |
Outer_Full |
||||||||||||||||||
|
SCC1/CC2 |
CP-OFDM QPSK |
Outer_Full |
|||||||||||||||||||
|
Wgap |
N/A |
N/A |
|||||||||||||||||||
|
SCC2/CC3 |
N/A |
N/A |
|||||||||||||||||||
|
SCC3/CC4 |
N/A |
N/A |
|||||||||||||||||||
|
SCC4/CC5 |
N/A |
N/A |
|||||||||||||||||||
|
SCC5/CC6 |
N/A |
N/A |
|||||||||||||||||||
|
4 |
PCC/CC1 |
CP-OFDM 16QAM |
Outer_Full |
||||||||||||||||||
|
SCC1/CC2 |
CP-OFDM 16QAM |
Outer_Full |
|||||||||||||||||||
|
Wgap |
N/A |
N/A |
|||||||||||||||||||
|
SCC2/CC3 |
N/A |
N/A |
|||||||||||||||||||
|
SCC3/CC4 |
N/A |
N/A |
|||||||||||||||||||
|
SCC4/CC5 |
N/A |
N/A |
|||||||||||||||||||
|
SCC5/CC6 |
N/A |
N/A |
|||||||||||||||||||
|
5 |
PCC/CC1 |
CP-OFDM 64QAM |
Outer_Full |
||||||||||||||||||
|
SCC1/CC2 |
CP-OFDM 64QAM |
Outer_Full |
|||||||||||||||||||
|
Wgap |
N/A |
N/A |
|||||||||||||||||||
|
SCC2/CC3 |
N/A |
N/A |
|||||||||||||||||||
|
SCC3/CC4 |
N/A |
N/A |
|||||||||||||||||||
|
SCC4/CC5 |
N/A |
N/A |
|||||||||||||||||||
|
SCC5/CC6 |
N/A |
N/A |
|||||||||||||||||||
|
Default Test Settings for a CA_nX(D-G)_UL_nXD, CA_nX(D-O)_UL_nXD Configuration (400MHz <= Cumulative aggregated BWchannel <800MHz) |
|||||||||||||||||||||
|
1 |
PCC/CC1 |
200MHz |
Default |
N/A for this |
DFT-s-OFDM QPSK |
Outer_Full |
|||||||||||||||
|
SCC1/CC2 |
200MHz |
test |
DFT-s-OFDM QPSK |
Outer_Full |
|||||||||||||||||
|
Wgap |
190MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC2/CC3 |
100MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC3/CC4 |
100MHz |
N/A |
N/A |
||||||||||||||||||
|
2 |
PCC/CC1 |
200MHz |
CP-OFDM QPSK |
Outer_Full |
|||||||||||||||||
|
SCC1/CC2 |
200MHz |
CP-OFDM QPSK |
Outer_Full |
||||||||||||||||||
|
Wgap |
190MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC2/CC3 |
100MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC3/CC4 |
100MHz |
N/A |
N/A |
||||||||||||||||||
|
3 |
PCC/CC1 |
200MHz |
CP-OFDM 16QAM |
Outer_Full |
|||||||||||||||||
|
SCC1/CC2 |
200MHz |
CP-OFDM 16QAM |
Outer_Full |
||||||||||||||||||
|
Wgap |
190MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC2/CC3 |
100MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC3/CC4 |
100MHz |
N/A |
N/A |
||||||||||||||||||
|
4 |
PCC/CC1 |
200MHz |
CP-OFDM 64QAM |
Outer_Full |
|||||||||||||||||
|
SCC1/CC2 |
200MHz |
CP-OFDM 64QAM |
Outer_Full |
||||||||||||||||||
|
Wgap |
190MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC2/CC3 |
100MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC3/CC4 |
100MHz |
N/A |
N/A |
||||||||||||||||||
|
Default Test Settings for a CA_nX(D-G)_UL_nXG, CA_nX(D-O)_UL_nXO Configuration (400MHz <= Cumulative aggregated BWchannel <800MHz) |
|||||||||||||||||||||
|
1 |
PCC/CC1 |
100MHz |
Default |
N/A for this |
DFT-s-OFDM QPSK |
Outer_Full |
|||||||||||||||
|
SCC1/CC2 |
100MHz |
test |
DFT-s-OFDM QPSK |
Outer_Full |
|||||||||||||||||
|
Wgap |
190MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC2/CC3 |
200MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC3/CC4 |
200MHz |
N/A |
N/A |
||||||||||||||||||
|
2 |
PCC/CC1 |
100MHz |
CP-OFDM QPSK |
Outer_Full |
|||||||||||||||||
|
SCC1/CC2 |
100MHz |
CP-OFDM QPSK |
Outer_Full |
||||||||||||||||||
|
Wgap |
190MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC2/CC3 |
200MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC3/CC4 |
200MHz |
N/A |
N/A |
||||||||||||||||||
|
3 |
PCC/CC1 |
100MHz |
CP-OFDM 16QAM |
Outer_Full |
|||||||||||||||||
|
SCC1/CC2 |
100MHz |
CP-OFDM 16QAM |
Outer_Full |
||||||||||||||||||
|
Wgap |
190MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC2/CC3 |
200MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC3/CC4 |
200MHz |
N/A |
N/A |
||||||||||||||||||
|
4 |
PCC/CC1 |
100MHz |
c |
Outer_Full |
|||||||||||||||||
|
SCC1/CC2 |
100MHz |
CP-OFDM 64QAM |
Outer_Full |
||||||||||||||||||
|
Wgap |
190MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC2/CC3 |
200MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC3/CC4 |
200MHz |
N/A |
N/A |
||||||||||||||||||
|
Default Test Settings for a CA_nX(D-H)_UL_nXD, CA_nX(D-P)_UL_nXD, Configuration (400MHz <= Cumulative aggregated BWchannel < 800MHz) |
|||||||||||||||||||||
|
1 |
PCC/CC1 |
200MHz |
Default |
N/A for this |
DFT-s-OFDM QPSK |
Outer_Full |
|||||||||||||||
|
SCC1/CC2 |
200MHz |
test |
DFT-s-OFDM QPSK |
Outer_Full |
|||||||||||||||||
|
Wgap |
90MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC2/CC3 |
100MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC3/CC4 |
100MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC4/CC5 |
100MHz |
N/A |
N/A |
||||||||||||||||||
|
2 |
PCC/CC1 |
200MHz |
CP-OFDM QPSK |
Outer_Full |
|||||||||||||||||
|
SCC1/CC2 |
200MHz |
CP-OFDM QPSK |
Outer_Full |
||||||||||||||||||
|
Wgap |
90MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC2/CC3 |
100MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC3/CC4 |
100MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC4/CC5 |
100MHz |
N/A |
N/A |
||||||||||||||||||
|
3 |
PCC/CC1 |
200MHz |
CP-OFDM 16QAM |
Outer_Full |
|||||||||||||||||
|
SCC1/CC2 |
200MHz |
CP-OFDM 16QAM |
Outer_Full |
||||||||||||||||||
|
Wgap |
90MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC2/CC3 |
100MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC3/CC4 |
100MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC4/CC5 |
100MHz |
N/A |
N/A |
||||||||||||||||||
|
4 |
PCC/CC1 |
200MHz |
CP-OFDM 16QAM |
Outer_Full |
|||||||||||||||||
|
SCC1/CC2 |
200MHz |
CP-OFDM 16QAM |
Outer_Full |
||||||||||||||||||
|
Wgap |
90MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC2/CC3 |
100MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC3/CC4 |
100MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC4/CC5 |
100MHz |
N/A |
N/A |
||||||||||||||||||
|
Default Test Settings for a CA_nX(O-E)_UL_nXO Configuration (400MHz <= Cumulative aggregated BWchannel < 800MHz) |
|||||||||||||||||||||
|
1 |
PCC/CC1 |
100MHz |
Default |
N/A for this |
DFT-s-OFDM QPSK |
Outer_Full |
|||||||||||||||
|
SCC1/CC2 |
100MHz |
test |
DFT-s-OFDM QPSK |
Outer_Full |
|||||||||||||||||
|
Wgap |
90MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC2/CC3 |
100MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC3/CC4 |
200MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC4/CC5 |
200MHz |
N/A |
N/A |
||||||||||||||||||
|
2 |
PCC/CC1 |
100MHz |
CP-OFDM QPSK |
Outer_Full |
|||||||||||||||||
|
SCC1/CC2 |
100MHz |
CP-OFDM QPSK |
Outer_Full |
||||||||||||||||||
|
Wgap |
90MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC2/CC3 |
100MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC3/CC4 |
200MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC4/CC5 |
200MHz |
N/A |
N/A |
||||||||||||||||||
|
3 |
PCC/CC1 |
100MHz |
CP-OFDM 16QAM |
Outer_Full |
|||||||||||||||||
|
SCC1/CC2 |
100MHz |
CP-OFDM 16QAM |
Outer_Full |
||||||||||||||||||
|
Wgap |
90MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC2/CC3 |
100MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC3/CC4 |
200MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC4/CC5 |
200MHz |
N/A |
N/A |
||||||||||||||||||
|
4 |
PCC/CC1 |
100MHz |
CP-OFDM 16QAM |
Outer_Full |
|||||||||||||||||
|
SCC1/CC2 |
100MHz |
CP-OFDM 16QAM |
Outer_Full |
||||||||||||||||||
|
Wgap |
90MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC2/CC3 |
100MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC3/CC4 |
200MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC4/CC5 |
200MHz |
N/A |
N/A |
||||||||||||||||||
|
Default Test Settings for a CA_nX(D-I)_UL_nXD, CA_nX(D-Q)_UL_nXD Configuration (400MHz <= Cumulative aggregated BWchannel < 800MHz) |
|||||||||||||||||||||
|
1 |
PCC/CC1 |
100MHz |
Default |
N/A for this |
DFT-s-OFDM QPSK |
Outer_Full |
|||||||||||||||
|
SCC1/CC2 |
200MHz |
test |
DFT-s-OFDM QPSK |
Outer_Full |
|||||||||||||||||
|
Wgap |
90MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC2/CC3 |
100MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC3/CC4 |
100MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC4/CC5 |
100MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC5/CC6 |
100MHz |
N/A |
N/A |
||||||||||||||||||
|
2 |
PCC/CC1 |
100MHz |
CP-OFDM QPSK |
Outer_Full |
|||||||||||||||||
|
SCC1/CC2 |
200MHz |
CP-OFDM QPSK |
Outer_Full |
||||||||||||||||||
|
Wgap |
90MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC2/CC3 |
100MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC3/CC4 |
100MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC4/CC5 |
100MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC5/CC6 |
100MHz |
N/A |
N/A |
||||||||||||||||||
|
3 |
PCC/CC1 |
100MHz |
CP-OFDM 16QAM |
Outer_Full |
|||||||||||||||||
|
SCC1/CC2 |
200MHz |
CP-OFDM 16QAM |
Outer_Full |
||||||||||||||||||
|
Wgap |
90MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC2/CC3 |
100MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC3/CC4 |
100MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC4/CC5 |
100MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC5/CC6 |
100MHz |
N/A |
N/A |
||||||||||||||||||
|
4 |
PCC/CC1 |
100MHz |
CP-OFDM 16QAM |
Outer_Full |
|||||||||||||||||
|
SCC1/CC2 |
200MHz |
CP-OFDM 16QAM |
Outer_Full |
||||||||||||||||||
|
Wgap |
90MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC2/CC3 |
100MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC3/CC4 |
100MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC4/CC5 |
100MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC5/CC6 |
100MHz |
N/A |
N/A |
||||||||||||||||||
|
Default Test Settings for a CA_nX(G-I)_UL_nXG Configuration (400MHz <= Cumulative aggregated BWchannel < 800MHz) |
|||||||||||||||||||||
|
1 |
PCC/CC1 |
100MHz |
Default |
N/A for this |
DFT-s-OFDM QPSK |
Outer_Full |
|||||||||||||||
|
SCC1/CC2 |
100MHz |
test |
DFT-s-OFDM QPSK |
Outer_Full |
|||||||||||||||||
|
Wgap |
190MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC2/CC3 |
100MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC3/CC4 |
100MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC4/CC5 |
100MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC5/CC6 |
100MHz |
N/A |
N/A |
||||||||||||||||||
|
2 |
PCC/CC1 |
100MHz |
CP-OFDM QPSK |
Outer_Full |
|||||||||||||||||
|
SCC1/CC2 |
100MHz |
CP-OFDM QPSK |
Outer_Full |
||||||||||||||||||
|
Wgap |
190MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC2/CC3 |
100MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC3/CC4 |
100MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC4/CC5 |
100MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC5/CC6 |
100MHz |
N/A |
N/A |
||||||||||||||||||
|
3 |
PCC/CC1 |
100MHz |
CP-OFDM 16QAM |
Outer_Full |
|||||||||||||||||
|
SCC1/CC2 |
100MHz |
CP-OFDM 16QAM |
Outer_Full |
||||||||||||||||||
|
Wgap |
190MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC2/CC3 |
100MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC3/CC4 |
100MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC4/CC5 |
100MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC5/CC6 |
100MHz |
N/A |
N/A |
||||||||||||||||||
|
4 |
PCC/CC1 |
100MHz |
CP-OFDM 16QAM |
Outer_Full |
|||||||||||||||||
|
SCC1/CC2 |
100MHz |
CP-OFDM 16QAM |
Outer_Full |
||||||||||||||||||
|
Wgap |
190MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC2/CC3 |
100MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC3/CC4 |
100MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC4/CC5 |
100MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC5/CC6 |
100MHz |
N/A |
N/A |
||||||||||||||||||
|
Default Test Settings for a CA_nX(D-O)_UL_nXD Configuration (Cumulative aggregated BWchannel <400MHz) |
|||||||||||||||||||||
|
1 |
PCC/CC1 |
50MHz |
Default |
N/A for this |
CP-OFDM QPSK |
Outer_Full |
|||||||||||||||
|
SCC1/CC2 |
200MHz |
test |
CP-OFDM QPSK |
Outer_Full |
|||||||||||||||||
|
Wgap |
40MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC2/CC3 |
50MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC3/CC4 |
50MHz |
N/A |
N/A |
||||||||||||||||||
|
2 |
PCC/CC1 |
50MHz |
CP-OFDM 16QAM |
Outer_Full |
|||||||||||||||||
|
SCC1/CC2 |
200MHz |
CP-OFDM 16QAM |
Outer_Full |
||||||||||||||||||
|
Wgap |
40MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC2/CC3 |
50MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC3/CC4 |
50MHz |
N/A |
N/A |
||||||||||||||||||
|
3 |
PCC/CC1 |
50MHz |
CP-OFDM 64QAM |
Outer_Full |
|||||||||||||||||
|
SCC1/CC2 |
200MHz |
CP-OFDM 64QAM |
Outer_Full |
||||||||||||||||||
|
Wgap |
40MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC2/CC3 |
50MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC3/CC4 |
50MHz |
N/A |
N/A |
||||||||||||||||||
|
Default Test Settings for a CA_nX(D-O)_UL_nXO Configuration (Cumulative aggregated BWchannel <400MHz) |
|||||||||||||||||||||
|
1 |
PCC/CC1 |
50MHz |
Default |
N/A for this |
N/A |
N/A |
|||||||||||||||
|
SCC1/CC2 |
200MHz |
test |
N/A |
N/A |
|||||||||||||||||
|
Wgap |
40MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC2/CC3 |
50MHz |
CP-OFDM QPSK |
Outer_Full |
||||||||||||||||||
|
SCC3/CC4 |
50MHz |
CP-OFDM QPSK |
Outer_Full |
||||||||||||||||||
|
2 |
PCC/CC1 |
50MHz |
N/A |
N/A |
|||||||||||||||||
|
SCC1/CC2 |
200MHz |
N/A |
N/A |
||||||||||||||||||
|
Wgap |
40MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC2/CC3 |
50MHz |
CP-OFDM 16QAM |
Outer_Full |
||||||||||||||||||
|
SCC3/CC4 |
50MHz |
CP-OFDM 16QAM |
Outer_Full |
||||||||||||||||||
|
3 |
PCC/CC1 |
50MHz |
N/A |
N/A |
|||||||||||||||||
|
SCC1/CC2 |
200MHz |
N/A |
N/A |
||||||||||||||||||
|
Wgap |
40MHz |
N/A |
N/A |
||||||||||||||||||
|
SCC2/CC3 |
50MHz |
CP-OFDM 64QAM |
Outer_Full |
||||||||||||||||||
|
SCC3/CC4 |
50MHz |
CP-OFDM 64QAM |
Outer_Full |
||||||||||||||||||
|
NOTE 1: The specific configuration of each RB allocation is defined in Table 6.1-1. NOTE 2: PCC/CCi and SCC/CCj means PCC is on component carrier CCi and SCC is on component carrier CCj, with CCi or CCj frequencies defined in TS38.508-1 [10]. |
|||||||||||||||||||||
Table 6.2A.2.1.4.1-7: Intra-band Contiguous UL CA Test Configuration Table (Power Class 2, 3 and 4, Non-contiguous allocation)
|
Default Conditions |
||||||
|
Test Environment as specified in TS 38.508-1 [10] subclause 4.1 |
Normal |
|||||
|
Test Frequencies as specified in TS 38.508-1 [10] subclause 4.3.1.2.3 for different CA bandwidth classes |
Mid range |
|||||
|
Test CC Combination setting (aggregated BW of the CA configuration) as specified in Table 5.5A.1-1, 5.5A.2-1 and 5.5A.2-2 for the CA Configuration across bandwidth combination sets supported by the UE |
Highest aggregated channel bandwidth of the CA configuration |
|||||
|
Test SCS as specified in Table 5.3.5-1 |
120 kHz |
|||||
|
Test Parameters |
||||||
|
Test ID |
CC & Mapping (NOTE 2) |
ChBw(MHz) |
Test frequency |
DL RB allocation |
UL Modulation |
UL RB allocation |
|
Default Test Settings for a CA_XG, CA_nXO Configuration (Cumulative aggregated BWchannel < 400MHz) |
||||||
|
1 |
PCC/CC1 |
Default |
Default |
N/A for this |
DFT-s-OFDM QPSK |
Outer_1RB_Left |
|
SCC/CC2 |
test |
DFT-s-OFDM QPSK |
Outer_1RB_Right |
|||
|
2 |
PCC/CC1 |
DFT-s-OFDM Pi/2 BPSK |
[Outer_0.9_Left] |
|||
|
SCC/CC2 |
DFT-s-OFDM Pi/2 BPSK |
[Outer_0.9_Right] |
||||
|
3 |
PCC/CC1 |
DFT-s-OFDM Pi/2 QPSK |
[Outer_0.9_Left] |
|||
|
SCC/CC2 |
DFT-s-OFDM Pi/2 QPSK |
[Outer_0.9_Right] |
||||
|
NOTE 1: The specific configuration of each RB allocation is defined in Table 6.1-1. NOTE 2: PCC/CCi and SCC/CCj means PCC is on component carrier CCi and SCC is on component carrier CCj, with CCi or CCj frequencies defined in TS38.508-1 [10]. |
||||||
1. Connection between SS and UE is shown in TS 38.508-1 [10] Annex A, Figure A.3.3.1.1 for TE diagram and Figure A.3.4.1.1 for UE diagram.
2. The parameter settings for the cell are set up according to TS 38.508-1 [10] subclause 4.4.3.
3. Downlink signals are initially set up according to Annex C.0, C.1 and C.3.0 and TS 38.508-1 [10] subclause 5.2.1.1.1, and uplink signals according to Annex G.0, G.1 and G.3.0.
4. The UL Reference Measurement channels are set according to Table 6.2A.2.1.4.1-1 to Table 6.2A.2.1.4.1-7.
5. Propagation conditions are set according to Annex B.0.
6. Ensure the UE is in state RRC_CONNECTED with generic procedure parameters Connectivity NR, Connected without release On, Test Mode On and Test Loop Function On according to TS 38.508-1 [10] clause 4.5. Message contents are defined in clause 6.2A.2.1.4.3.
6.2A.2.1.4.2 Test procedure
1. Configure SCC according to Annex C.0, C.1, C.2 and Annex C.3.0 for all downlink physical channels
2. The SS shall configure SCC as per TS 38.508-1 [10] subclause 5.5.1 Procedure to configure SCC(s) for NR RF CA testing. Message contents are defined in subclause 6.2A.2.1.4.3.
3. SS activates SCC by sending the activation MAC CE (Refer TS 38.321, clauses 5.9, 6.1.3.10). Wait for at least 2 seconds (Refer TS 38.133[25], clause 9.3).
4. SS sends uplink scheduling information for each UL HARQ process via PDCCH DCI format 0_1 for C_RNTI to schedule the UL RMC according to Table 6.2A.2.1.4.1-1 to Table 6.2A.2.1.4.1-7. Since the UL has no payload and no loopback data to send the UE sends uplink MAC padding bits on the UL RMC.
5. Set the UE in the Tx beam peak direction found with a 3D EIRP scan as performed in Annex K.1.1. Allow at least BEAM_SELECT_WAIT_TIME (NOTE 1) for the UE Tx beam selection to complete.
6. Send continuously uplink power control "up" commands in every uplink scheduling information to the UE; allow at least 200 msec starting from the first TPC command in this step to ensure that the UE transmits at its maximum output power. Allow at least BEAM_SELECT_WAIT_TIME (NOTE 1) for the UE Tx beam selection to complete.
7. SS activates the UE Beamlock Function (UBF) by performing the procedure as specified in TS 38.508-1 [10] clause 4.9.2 using condition Tx only.
8. Measure UE EIRP in the Tx beam peak direction in the accumulative aggregated channel bandwidth of the radio access mode according to the test configuration, which shall meet the requirements described in 6.2A.2.1.5. EIRP test procedure is defined in Annex K.1.3. The measuring duration is one active uplink subframe. EIRP is calculated considering both polarizations, theta and phi.
9. SS deactivates the UE Beamlock Function (UBF) by performing the procedure as specified in TS 38.508-1 [10] clause 4.9.3.
NOTE 1: The BEAM_SELECT_WAIT_TIME default value is defined in Annex K.1.1.
NOTE 2: When switching to DFT-s-OFDM waveform, as specified in the test configuration table 6.2A.2.1.4.1-1 to Table 6.2A.2.1.4.1-7, send an NR RRCReconfiguration message according to TS 38.508-1 [10] clause 4.6.3 Table 4.6.3-118 PUSCH-Config with TRANSFORM_PRECODER_ENABLED condition.
6.2A.2.1.4.3 Message contents
Message contents are according to TS 38.508-1 [10] subclause 4.6. In test procedure step 1, for SCC configuration there are no additional message contents.
6.2A.2.1.5 Test requirement
The EIRP derived in step 8 shall be within the range prescribed by the nominal maximum output power and tolerance in the applicable table from Table 6.2A.2.1.5-1 to Table 6.2A.2.1.5-17.
Table 6.2A.2.1.5-1: MPR requirements for Intra-band Contiguous UL CA (Power Class 1, MPRnarrow)
|
Test ID |
Band |
Min peak EIRP (dBm) |
MPR (dB) |
T(MPR) (dB) |
Lower limit (dBm) |
Upper limit (dBm) |
|
1 |
n257, n258, n261 |
40.0 |
14.4 |
[7.0] |
[18.6]-TT |
55 |
|
1 |
n260 |
38.0 |
14.4 |
[7.0] |
[16.6]-TT |
55 |
|
2 |
n257, n258, n261 |
40.0 |
14.4 |
[7.0] |
[18.6]-TT |
55 |
|
2 |
n260 |
38.0 |
14.4 |
[7.0] |
[16.6]-TT |
55 |
|
3 |
n257, n258, n261 |
40.0 |
10 |
[5] |
[25.0]-TT |
55 |
|
3 |
n260 |
38.0 |
10 |
[5] |
[23.0]-TT |
55 |
|
4 |
n257, n258, n261 |
40.0 |
10 |
[5] |
[25.0]-TT |
55 |
|
4 |
n260 |
38.0 |
10 |
[5] |
[23.0]-TT |
55 |
|
NOTE 1: TT for each band and accumulative aggregated bandwidth is specified in Table 6.2A.2.1.5-5. |
||||||
Table 6.2A.2.1.5-2: MPR requirements for Intra-band Contiguous UL CA (Power Class 1, single CC MPR requirement)
|
Test ID |
Band |
Min peak EIRP (dBm) |
MPR (dB) |
T(MPR) (dB) |
Lower limit (dBm) |
Upper limit (dBm) |
|
Test requirements for a CA_nXG, CA_nXO Configuration (Cumulative aggregated BWchannel <= 200MHz) |
||||||
|
1 |
n257, n258, n261 |
40.0 |
5.5 |
[5.0] |
[29.5]-TT |
55 |
|
1 |
n260 |
38.0 |
5.5 |
[5.0] |
[27.5]-TT |
55 |
|
2 |
n257, n258, n261 |
40.0 |
3.0 |
[2.0] |
[35.0]-TT |
55 |
|
2 |
n260 |
38.0 |
3.0 |
[2.0] |
[33.0]-TT |
55 |
|
Test requirements for a CA_nXD Configuration (Cumulative aggregated BWchannel <= 400MHz) |
||||||
|
1 |
n257, n258, n261 |
40.0 |
5.5 |
[5.0] |
[29.5]-TT |
55 |
|
1 |
n260 |
38.0 |
5.5 |
[5.0] |
[27.5]-TT |
55 |
|
2 |
n257, n258, n261 |
40.0 |
3.0 |
[2.0] |
[35.0]-TT |
55 |
|
2 |
n260 |
38.0 |
3.0 |
[2.0] |
[33.0]-TT |
55 |
|
3 |
n257, n258, n261 |
40.0 |
3.5 |
[3.0] |
[33.5]-TT |
55 |
|
3 |
n260 |
38.0 |
3.5 |
[3.0] |
[31.5]-TT |
55 |
|
NOTE 1: TT for each band and accumulative aggregated bandwidth is specified in Table 6.2A.2.1.5-5. |
||||||
Table 6.2A.2.1.5-3: MPR requirements for Intra-band Contiguous UL CA (Power Class 1, MPRC_CA)
|
Test ID |
Band |
Min peak EIRP (dBm) |
MPR (dB) |
T(MPR) (dB) |
Lower limit (dBm) |
Upper limit (dBm) |
|
Test requirements for a CA_nXB, CA_nXC_UL_nXB Configuration (800MHz <= Cumulative aggregated BWchannel <= 1400MHz) |
||||||
|
1 |
n257, n258, n261 |
40.0 |
[8.2] |
[5.0] |
[26.8]-TT |
55 |
|
1 |
n260 |
38.0 |
[8.2] |
[5.0] |
[24.8]-TT |
55 |
|
2 |
n257, n258, n261 |
40.0 |
[9.7] |
[5.0] |
[25.3]-TT |
55 |
|
2 |
n260 |
38.0 |
[9.7] |
[5.0] |
[23.3]-TT |
55 |
|
3 |
n257, n258, n261 |
40.0 |
[9.2] |
[5.0] |
[25.8]-TT |
55 |
|
3 |
n260 |
38.0 |
[9.2] |
[5.0] |
[23.8]-TT |
55 |
|
4 |
n257, n258, n261 |
40.0 |
[8.7] |
[5.0] |
[26.3]-TT |
55 |
|
4 |
n260 |
38.0 |
[8.7] |
[5.0] |
[24.3]-TT |
55 |
|
5 |
n257, n258, n261 |
40.0 |
[11.2] |
[7.0] |
[21.8]-TT |
55 |
|
5 |
n260 |
38.0 |
[11.2] |
[7.0] |
[19.8]-TT |
55 |
|
Test requirements for a CA_nXD, CA_nXB Configuration (400MHz <= Cumulative aggregated BWchannel < 800MHz) |
||||||
|
1 |
n257, n258, n261 |
40.0 |
7.7 |
[5.0] |
[27.3]-TT |
55 |
|
1 |
n260 |
38.0 |
7.7 |
[5.0] |
[25.3]-TT |
55 |
|
2 |
n257, n258, n261 |
40.0 |
8.7 |
[5.0] |
[26.3]-TT |
55 |
|
2 |
n260 |
38.0 |
8.7 |
[5.0] |
[24.3]-TT |
55 |
|
3 |
n257, n258, n261 |
40.0 |
10.7 |
[7.0] |
[22.3]-TT |
55 |
|
3 |
n260 |
38.0 |
10.7 |
[7.0] |
[20.3]-TT |
55 |
|
Test requirements for a CA_nXG, CA_nXO, CA_nXD Configuration (Cumulative aggregated BWchannel < 400MHz) |
||||||
|
1 |
n257, n258, n261 |
40.0 |
5.5 |
[5.0] |
[29.5]-TT |
55 |
|
1 |
n260 |
38.0 |
5.5 |
[5.0] |
[27.5]-TT |
55 |
|
2 |
n257, n258, n261 |
40.0 |
6.5 |
[5.0] |
[28.5]-TT |
55 |
|
2 |
n260 |
38.0 |
6.5 |
[5.0] |
[26.5]-TT |
55 |
|
3 |
n257, n258, n261 |
40.0 |
9.0 |
[5.0] |
[26.0]-TT |
55 |
|
3 |
n260 |
38.0 |
9.0 |
[5.0] |
[24.0]-TT |
55 |
|
Test requirements for a CA_nX(D-G)_UL_nXD, CA_nX(D-G)_UL_nXG, CA_nX(D-O)_UL_nXD, CA_nX(D-O)_UL_nXO, CA_nX(D-H)_UL_nXD, CA_nX(D-P)_UL_nXD, CA_nX(E-O)_UL_nXO, CA_nX(D-I)_UL_nXD, CA_nX(D-Q)_UL_nXD, CA_nX(G-I)_UL_nXG Configuration (800MHz <= Cumulative aggregated BWchannel <= 1400MHz) |
||||||
|
1 |
n257, n258, n261 |
40.0 |
[8.2] |
[5.0] |
[26.8] –TT |
55 |
|
1 |
n260 |
38.0 |
[8.2] |
[5.0] |
[24.8] –TT |
55 |
|
2 |
n257, n258, n261 |
40.0 |
[9.7] |
[5.0] |
[25.3] –TT |
55 |
|
2 |
n260 |
38.0 |
[9.7] |
[5.0] |
[23.3] –TT |
55 |
|
3 |
n257, n258, n261 |
40.0 |
[9.2] |
[5.0] |
[25.8] –TT |
55 |
|
3 |
n260 |
38.0 |
[9.2] |
[5.0] |
[23.8] –TT |
55 |
|
4 |
n257, n258, n261 |
40.0 |
[8.7] |
[5.0] |
[26.3] –TT |
55 |
|
4 |
n260 |
38.0 |
[8.7] |
[5.0] |
[24.3] –TT |
55 |
|
5 |
n257, n258, n261 |
40.0 |
[11.2] |
[7.0] |
[21.8] –TT |
55 |
|
5 |
n260 |
38.0 |
[11.2] |
[7.0] |
[19.8] –TT |
55 |
|
Test requirements for a CA_nX(D-G)_UL_nXD, CA_nX(D-O)_UL_nXD, CA_nX(D-G)_UL_nXG, CA_nX(D-O)_UL_nXO, CA_nX(D-H)_UL_nXD, CA_nX(D-P)_UL_nXD, CA_nX(O-E)_UL_nXO, CA_nX(D-I)_UL_nXD, CA_nX(D-Q)_UL_nXD, CA_nX(G-I)_UL_nXG Configuration (400MHz <= Cumulative aggregated BWchannel <800MHz) |
||||||
|
1 |
n257, n258, n261 |
40.0 |
7.7 |
[5.0] |
[27.3]-TT |
55 |
|
1 |
n260 |
38.0 |
7.7 |
[5.0] |
[25.3]-TT |
55 |
|
2 |
n257, n258, n261 |
40.0 |
8.7 |
[5.0] |
[26.3]-TT |
55 |
|
2 |
n260 |
38.0 |
8.7 |
[5.0] |
[24.3]-TT |
55 |
|
3 |
n257, n258, n261 |
40.0 |
10.7 |
[7.0] |
[22.3]-TT |
55 |
|
3 |
n260 |
38.0 |
10.7 |
[7.0] |
[20.3]-TT |
55 |
|
Test requirements for a CA_nX(D-O)_UL_nXD, CA_nX(D-O)_UL_nXO Configuration (Cumulative aggregated BWchannel <400MHz) |
||||||
|
1 |
n257, n258, n261 |
40.0 |
5.5 |
[5.0] |
[29.5]-TT |
55 |
|
1 |
n260 |
38.0 |
5.5 |
[5.0] |
[27.5]-TT |
55 |
|
2 |
n257, n258, n261 |
40.0 |
6.5 |
[5.0] |
[28.5]-TT |
55 |
|
2 |
n260 |
38.0 |
6.5 |
[5.0] |
[26.5]-TT |
55 |
|
3 |
n257, n258, n261 |
40.0 |
9.0 |
[5.0] |
[26.0]-TT |
55 |
|
3 |
n260 |
38.0 |
9.0 |
[5.0] |
[24.0]-TT |
55 |
|
NOTE 1: TT for each band and accumulative aggregated bandwidth is specified in Table 6.2A.2.1.5-5. |
||||||
Table 6.2A.2.1.5-4: MPR requirements for Intra-band Contiguous UL CA (Power Class 1, Non-contiguous allocation)
|
Test ID |
Band |
Min peak EIRP (dBm) |
MPR (dB) |
T(MPR) (dB) |
Lower limit (dBm) |
Upper limit (dBm) |
|
Test requirements for a CA_nXB, CA_nXD, CA_XG, CA_nXO Configuration |
||||||
|
1 |
n257, n258, n261 |
40.0 |
[14.4] |
[7.0] |
[18.6] –TT |
55 |
|
1 |
n260 |
38.0 |
[14.4] |
[7.0] |
[16.6] –TT |
55 |
|
2 |
n257, n258, n261 |
FFS |
FFS |
FFS |
FFS |
FFS |
|
2 |
n260 |
FFS |
FFS |
FFS |
FFS |
FFS |
|
3 |
n257, n258, n261 |
FFS |
FFS |
FFS |
FFS |
FFS |
|
3 |
n260 |
FFS |
FFS |
FFS |
FFS |
FFS |
|
Test requirements for a CA_nX(D-G), CA_nX(D-O) Configuration |
||||||
|
1 |
n257, n258, n261 |
40.0 |
[14.4] |
[7.0] |
[18.6] –TT |
55 |
|
1 |
n260 |
38.0 |
[14.4] |
[7.0] |
[16.6] –TT |
55 |
|
2 |
n257, n258, n261 |
FFS |
FFS |
FFS |
FFS |
FFS |
|
2 |
n260 |
FFS |
FFS |
FFS |
FFS |
FFS |
|
3 |
n257, n258, n261 |
FFS |
FFS |
FFS |
FFS |
FFS |
|
3 |
n260 |
FFS |
FFS |
FFS |
FFS |
FFS |
|
NOTE 1: TT for each band and accumulative aggregated bandwidth is specified in Table 6.2A.2.1.5-5. |
||||||
Table 6.2A.2.1.5-5: Test Tolerance (MPR for CA for Power class 1)
FFS
Table 6.2A.2.1.5-6: MPR requirements for Intra-band Contiguous UL CA (Power Class 2, single CC MPR requirement)
|
Test ID |
Band |
Min peak EIRP (dBm) |
MPR (dB) |
T(MPR) (dB) |
Lower limit (dBm) |
Upper limit (dBm) |
|
Test requirements for a CA_nXG, CA_nXO Configuration (Cumulative aggregated BWchannel <= 200MHz) |
||||||
|
1 |
n257, n258, n261 |
29 |
0 |
0 |
29.0-TT |
43 |
|
2 |
n257, n258, n261 |
29 |
2 |
[1.5] |
[25.5]-TT |
43 |
|
Test requirements for a CA_nXD Configuration (Cumulative aggregated BWchannel <= 400MHz) |
||||||
|
1 |
n257, n258, n261 |
29 |
0 |
0 |
29.0-TT |
43 |
|
2 |
n257, n258, n261 |
29 |
3 |
[2.0] |
[24.0]-TT |
43 |
|
NOTE 1: TT for each band and accumulative aggregated bandwidth is specified in Table 6.2A.2.1.5-9. |
||||||
Table 6.2A.2.1.5-7: MPR requirements for Intra-band Contiguous UL CA (Power Class 2, MPRC_CA)
|
Test ID |
Band |
Min peak EIRP (dBm) |
MPR (dB) |
T(MPR) (dB) |
Lower limit (dBm) |
Upper limit (dBm) |
|
Test requirements for a CA_nXB, nXC_UL_nXB Configuration (800MHz <= Cumulative aggregated BWchannel <= 1400MHz) |
||||||
|
1 |
n257, n258, n261 |
29 |
[8.2] |
[5.0] |
[15.8]-TT |
43 |
|
2 |
n257, n258, n261 |
29 |
[9.3] |
[5.0] |
[14.7]-TT |
43 |
|
3 |
n257, n258, n261 |
29 |
[8.0] |
[5.0] |
[16.0]-TT |
43 |
|
4 |
n257, n258, n261 |
29 |
[9.2] |
[5.0] |
[14.8]-TT |
43 |
|
5 |
n257, n258, n261 |
29 |
[11.2] |
[7.0] |
[10.8]-TT |
43 |
|
Test requirements for a CA_nXD, CA_nXB Configuration (400MHz <= Cumulative aggregated BWchannel < 800MHz) |
||||||
|
1 |
n257, n258, n261 |
29 |
7.7 |
[5.0] |
[16.3]-TT |
43 |
|
2 |
n257, n258, n261 |
29 |
7.5 |
[5.0] |
[16.5]-TT |
43 |
|
3 |
n257, n258, n261 |
29 |
8.7 |
[5.0] |
[15.3]-TT |
43 |
|
4 |
n257, n258, n261 |
29 |
10.7 |
[7.0] |
[11.3]-TT |
43 |
|
Test requirements for a CA_nXG, CA_nXO, CA_nXD Configuration (Cumulative aggregated BWchannel < 400MHz) |
||||||
|
1 |
n257, n258, n261 |
29 |
5 |
[4.0] |
[20.0]-TT |
43 |
|
2 |
n257, n258, n261 |
29 |
6.5 |
[5.0] |
[17.5]-TT |
43 |
|
3 |
n257, n258, n261 |
29 |
9 |
[5.0] |
[15.0]-TT |
43 |
|
Test requirements for a CA_nX(D-G) )_UL_nXD, CA_nX(D-G)_UL_nXG, CA_nX(D-O)_UL_nXD, CA_nX(D-O)_UL_nXO, CA_nX(D-H)_UL_nXD, CA_nX(D-P)_UL_nXD, CA_nX(E-O)_UL_nXO, CA_nX(D-I)_UL_nXD, CA_nX(D-Q)_UL_nXD, CA_nX(G-I)_UL_nXG Configuration (800MHz <= Cumulative aggregated BWchannel <= 1400MHz) |
||||||
|
1 |
n257, n258, n261 |
29 |
[8.2] |
[5.0] |
[15.8]-TT |
43 |
|
2 |
n257, n258, n261 |
29 |
[9.3] |
[5.0] |
[14.7]-TT |
43 |
|
3 |
n257, n258, n261 |
29 |
[8.0] |
[5.0] |
[16.0]-TT |
43 |
|
4 |
n257, n258, n261 |
29 |
[9.2] |
[5.0] |
[14.8]-TT |
43 |
|
5 |
n257, n258, n261 |
29 |
[11.2] |
[7.0] |
[10.8]-TT |
43 |
|
Test requirements for a CA_nX(D-G)_UL_nXD, CA_nX(D-O)_UL_nXD, CA_nX(D-G)_UL_nXG, CA_nX(D-O)_UL_nXO, CA_nX(D-H)_UL_nXD, CA_nX(D-P)_UL_nXD, CA_nX(O-E)_UL_nXO, CA_nX(D-I)_UL_nXD, CA_nX(D-Q)_UL_nXD, CA_nX(G-I)_UL_nXG Configuration (400MHz <= Cumulative aggregated BWchannel < 800MHz) |
||||||
|
1 |
n257, n258, n261 |
29 |
7.7 |
[5.0] |
[16.3]-TT |
43 |
|
2 |
n257, n258, n261 |
29 |
7.5 |
[5.0] |
[16.5]-TT |
43 |
|
3 |
n257, n258, n261 |
29 |
8.7 |
[5.0] |
[15.3]-TT |
43 |
|
4 |
n257, n258, n261 |
29 |
10.7 |
[7.0] |
[11.3]-TT |
43 |
|
Test requirements for a CA_nX(D-O)_UL_nXD, CA_nX(D-O)_UL_nXO Configuration (Cumulative aggregated BWchannel < 400MHz) |
||||||
|
1 |
n257, n258, n261 |
29 |
7.7 |
[5.0] |
[16.3]-TT |
43 |
|
2 |
n257, n258, n261 |
29 |
7.5 |
[5.0] |
[16.5]-TT |
43 |
|
3 |
n257, n258, n261 |
29 |
8.7 |
[5.0] |
[15.3]-TT |
43 |
|
NOTE 1: TT for each band and accumulative aggregated bandwidth is specified in Table 6.2A.2.1.5-9. |
||||||
Table 6.2A.2.1.5-8: MPR requirements for Intra-band Contiguous UL CA (Power Class 2, Non-contiguous allocation)
|
Test ID |
Band |
Min peak EIRP (dBm) |
MPR (dB) |
T(MPR) (dB) |
Lower limit (dBm) |
Upper limit (dBm) |
|
Test requirements for a CA_nXB, CA_nXD, CA_XG, CA_nXO Configuration |
||||||
|
1 |
n257, n258, n261 |
29 |
7 |
[5.0] |
[17.0] –TT |
43 |
|
2 |
n257, n258, n261 |
FFS |
FFS |
FFS |
FFS |
FFS |
|
3 |
n257, n258, n261 |
FFS |
FFS |
FFS |
FFS |
FFS |
|
NOTE 1: TT for each band and accumulative aggregated bandwidth is specified in Table 6.2A.2.1.5-9. |
||||||
Table 6.2A.2.1.5-9: Test Tolerance (MPR for CA for Power class 2)
FFS
Table 6.2A.2.1.5-10: MPR requirements for Intra-band Contiguous UL CA (Power Class 3, single CC MPR requirement)
|
Test ID |
Band |
Min peak EIRP (dBm) |
MPR (dB) |
T(MPR) (dB) |
Lower limit (dBm) |
Upper limit (dBm) |
|
Test requirements for a CA_nXG, CA_nXO Configuration (Cumulative aggregated BWchannel <= 200MHz) |
||||||
|
1 |
n257, n258, n261 |
22.4 |
0 |
0 |
22.4-TT |
43 |
|
1 |
n260 |
20.6 |
0 |
0 |
20.6-TT |
43 |
|
2 |
n257, n258, n261 |
22.4 |
2 |
[1.5] |
[18.9]-TT |
43 |
|
2 |
n260 |
20.6 |
2 |
[1.5] |
[17.1]-TT |
43 |
|
Test requirements for a CA_nXD Configuration (Cumulative aggregated BWchannel <= 400MHz) |
||||||
|
1 |
n257, n258, n261 |
22.4 |
0 |
0 |
22.4-TT |
43 |
|
1 |
n260 |
20.6 |
0 |
0 |
20.6-TT |
43 |
|
2 |
n257, n258, n261 |
22.4 |
3 |
[2.0] |
[17.4]-TT |
43 |
|
2 |
n260 |
20.6 |
3 |
[2.0] |
[15.6]-TT |
43 |
|
NOTE 1: TT for each band and accumulative aggregated bandwidth is specified in Table 6.2A.2.1.5-13. |
||||||
Table 6.2A.2.1.5-11: MPR requirements for Intra-band Contiguous UL CA (Power Class 3, MPRC_CA)
|
Test ID |
Band |
Min peak EIRP (dBm) |
MPR (dB) |
T(MPR) (dB) |
Lower limit (dBm) |
Upper limit (dBm) |
|
Test requirements for a CA_nXB, nXC_UL_nXB Configuration (Cumulative aggregated BWchannel <= 1400MHz) |
||||||
|
1 |
n257, n258, n261 |
22.4 |
[8.2] |
[5.0] |
[9.2]-TT |
43 |
|
1 |
n260 |
20.6 |
[8.2] |
[5.0] |
[7.4]-TT |
43 |
|
2 |
n257, n258, n261 |
22.4 |
[9.3] |
[5.0] |
[8.1]-TT |
43 |
|
2 |
n260 |
20.6 |
[9.3] |
[5.0] |
[6.3]-TT |
43 |
|
3 |
n257, n258, n261 |
22.4 |
[8.0] |
[5.0] |
[9.4]-TT |
43 |
|
3 |
n260 |
20.6 |
[8.0] |
[5.0] |
[7.6]-TT |
43 |
|
4 |
n257, n258, n261 |
22.4 |
[9.2] |
[5.0] |
[8.2]-TT |
43 |
|
4 |
n260 |
20.6 |
[9.2] |
[5.0] |
[6.4]-TT |
43 |
|
5 |
n257, n258, n261 |
22.4 |
[11.2] |
[7.0] |
[4.2]-TT |
43 |
|
5 |
n260 |
20.6 |
[11.2] |
[7.0] |
[2.4]-TT |
43 |
|
Test requirements for a CA_nXD, CA_nXB Configuration (Cumulative aggregated BWchannel < 800MHz) |
||||||
|
1 |
n257, n258, n261 |
22.4 |
7.7 |
[5.0] |
[9.7]-TT |
43 |
|
1 |
n260 |
20.6 |
7.7 |
[5.0] |
[7.9]-TT |
43 |
|
2 |
n257, n258, n261 |
22.4 |
7.5 |
[5.0] |
[9.9]-TT |
43 |
|
2 |
n260 |
20.6 |
7.5 |
[5.0] |
[8.1]-TT |
43 |
|
3 |
n257, n258, n261 |
22.4 |
8.7 |
[5.0] |
[8.7]-TT |
43 |
|
3 |
n260 |
20.6 |
8.7 |
[5.0] |
[6.9]-TT |
43 |
|
4 |
n257, n258, n261 |
22.4 |
10.7 |
[7.0] |
[4.7]-TT |
43 |
|
4 |
n260 |
20.6 |
10.7 |
[7.0] |
[2.9]-TT |
43 |
|
Test requirements for a CA_nXG, CA_nXO, CA_nXD Configuration (Cumulative aggregated BWchannel < 400MHz) |
||||||
|
1 |
n257, n258, n261 |
22.4 |
5 |
[4.0] |
[13.4]-TT |
43 |
|
1 |
n260 |
20.6 |
5 |
[4.0] |
[11.6]-TT |
43 |
|
2 |
n257, n258, n261 |
22.4 |
6.5 |
[5.0] |
[10.9]-TT |
43 |
|
2 |
n260 |
20.6 |
6.5 |
[5.0] |
[9.1]-TT |
43 |
|
3 |
n257, n258, n261 |
22.4 |
9 |
[5.0] |
[8.4]-TT |
43 |
|
3 |
n260 |
20.6 |
9 |
[5.0] |
[6.6]-TT |
43 |
|
Test requirements for a CA_nX(D-G) )_UL_nXD, CA_nX(D-G)_UL_nXG, CA_nX(D-O)_UL_nXD, CA_nX(D-O)_UL_nXO, CA_nX(D-H)_UL_nXD, CA_nX(D-P)_UL_nXD, CA_nX(E-O)_UL_nXO, CA_nX(D-I)_UL_nXD, CA_nX(D-Q)_UL_nXD, CA_nX(G-I)_UL_nXG Configuration (Cumulative aggregated BWchannel <= 1400MHz) |
||||||
|
1 |
n257, n258, n261 |
22.4 |
[8.2] |
[5.0] |
[9.2]-TT |
43 |
|
1 |
n260 |
20.6 |
[8.2] |
[5.0] |
[7.4]-TT |
43 |
|
2 |
n257, n258, n261 |
22.4 |
[9.3] |
[5.0] |
[8.1]-TT |
43 |
|
2 |
n260 |
20.6 |
[9.3] |
[5.0] |
[6.3]-TT |
43 |
|
3 |
n257, n258, n261 |
22.4 |
[8.0] |
[5.0] |
[9.4]-TT |
43 |
|
3 |
n260 |
20.6 |
[8.0] |
[5.0] |
[7.6]-TT |
43 |
|
4 |
n257, n258, n261 |
22.4 |
[9.2] |
[5.0] |
[8.2]-TT |
43 |
|
4 |
n260 |
20.6 |
[9.2] |
[5.0] |
[6.4]-TT |
43 |
|
5 |
n257, n258, n261 |
22.4 |
[11.2] |
[7.0] |
[4.2]-TT |
43 |
|
5 |
n260 |
20.6 |
[11.2] |
[7.0] |
[2.4]-TT |
43 |
|
Test requirements for a CA_nX(D-G)_UL_nXD, CA_nX(D-O)_UL_nXD, CA_nX(D-G)_UL_nXG, CA_nX(D-O)_UL_nXO, CA_nX(D-H)_UL_nXD, CA_nX(D-P)_UL_nXD, CA_nX(O-E)_UL_nXO, CA_nX(D-I)_UL_nXD, CA_nX(D-Q)_UL_nXD, CA_nX(G-I)_UL_nXG Configuration (Cumulative aggregated BWchannel < 800MHz) |
||||||
|
1 |
n257, n258, n261 |
22.4 |
7.7 |
[5.0] |
[9.7]-TT |
43 |
|
1 |
n260 |
20.6 |
7.7 |
[5.0] |
[7.9]-TT |
43 |
|
2 |
n257, n258, n261 |
22.4 |
7.5 |
[5.0] |
[9.9]-TT |
43 |
|
2 |
n260 |
20.6 |
7.5 |
[5.0] |
[8.1]-TT |
43 |
|
3 |
n257, n258, n261 |
22.4 |
8.7 |
[5.0] |
[8.7]-TT |
43 |
|
3 |
n260 |
20.6 |
8.7 |
[5.0] |
[6.9]-TT |
43 |
|
4 |
n257, n258, n261 |
22.4 |
10.7 |
[7.0] |
[4.7]-TT |
43 |
|
4 |
n260 |
20.6 |
10.7 |
[7.0] |
[2.9]-TT |
43 |
|
Test requirements for a CA_nX(D-O)_UL_nXD, CA_nX(D-O)_UL_nXO Configuration (Cumulative aggregated BWchannel < 400MHz) |
||||||
|
1 |
n257, n258, n261 |
22.4 |
5 |
[4.0] |
[13.4]-TT |
43 |
|
1 |
n260 |
20.6 |
5 |
[4.0] |
[11.6]-TT |
43 |
|
2 |
n257, n258, n261 |
22.4 |
6.5 |
[5.0] |
[10.9]-TT |
43 |
|
2 |
n260 |
20.6 |
6.5 |
[5.0] |
[9.1]-TT |
43 |
|
3 |
n257, n258, n261 |
22.4 |
9 |
[5.0] |
[8.4]-TT |
43 |
|
3 |
n260 |
20.6 |
9 |
[5.0] |
[6.6]-TT |
43 |
|
NOTE 1: TT for each band and accumulative aggregated bandwidth is specified in Table 6.2A.2.1.5-13. |
||||||
Table 6.2A.2.1.5-12: MPR requirements for Intra-band Contiguous UL CA (Power Class 3, Non-contiguous allocation)
|
Test ID |
Band |
Min peak EIRP (dBm) |
MPR (dB) |
T(MPR) (dB) |
Lower limit (dBm) |
Upper limit (dBm) |
|
Test requirements for a CA_nXB, CA_nXD, CA_XG, CA_nXO Configuration |
||||||
|
1 |
n257, n258, n261 |
22.4 |
7 |
[5.0] |
[10.4]-TT |
43 |
|
1 |
n260 |
20.6 |
7 |
[5.0] |
[8.6]-TT |
43 |
|
2 |
n257, n258, n261 |
FFS |
FFS |
FFS |
FFS |
FFS |
|
2 |
n260 |
FFS |
FFS |
FFS |
FFS |
FFS |
|
3 |
n257, n258, n261 |
FFS |
FFS |
FFS |
FFS |
FFS |
|
3 |
n260 |
FFS |
FFS |
FFS |
FFS |
FFS |
|
NOTE 1: TT for each band and accumulative aggregated bandwidth is specified in Table 6.2A.2.1.5-13. |
||||||
Table 6.2A.2.1.5-13: Test Tolerance (MPR for CA for Power class 3) (Aggregated BW ≤ 400MHz)
|
Test Metric |
FR2a |
FR2b |
|
Max device size ≤ 30 cm |
3.11 dB |
3.11 dB |
Table 6.2A.2.1.5-14: MPR requirements for Intra-band Contiguous UL CA (Power Class 4, single CC MPR requirement)
|
Test ID |
Band |
Min peak EIRP (dBm) |
MPR (dB) |
T(MPR) (dB) |
Lower limit (dBm) |
Upper limit (dBm) |
|
Test requirements for a CA_nXG, CA_nXO Configuration (Cumulative aggregated BWchannel <= 200MHz) |
||||||
|
1 |
n257, n258, n261 |
34 |
0 |
0 |
34.0-TT |
43 |
|
1 |
n260 |
31 |
0 |
0 |
31.0-TT |
43 |
|
2 |
n257, n258, n261 |
34 |
2 |
[1.5] |
[30.5]-TT |
43 |
|
2 |
n260 |
31 |
2 |
[1.5] |
[27.5]-TT |
43 |
|
Test requirements for a CA_nXD Configuration (Cumulative aggregated BWchannel <= 400MHz) |
||||||
|
1 |
n257, n258, n261 |
34 |
0 |
0 |
34.0-TT |
43 |
|
1 |
n260 |
31 |
0 |
0 |
31.0-TT |
43 |
|
2 |
n257, n258, n261 |
34 |
3 |
[2.0] |
[29.0]-TT |
43 |
|
2 |
n260 |
31 |
3 |
[2.0] |
[26.0]-TT |
43 |
|
NOTE 1: TT for each band and accumulative aggregated bandwidth is specified in Table 6.2A.2.1.5-17. |
||||||
Table 6.2A.2.1.5-15: MPR requirements for Intra-band Contiguous UL CA (Power Class 4, MPRC_CA)
|
Test ID |
Band |
Min peak EIRP (dBm) |
MPR (dB) |
T(MPR) (dB) |
Lower limit (dBm) |
Upper limit (dBm) |
|
Test requirements for a CA_nXB, nXC_UL_nXB Configuration (Cumulative aggregated BWchannel <= 1400MHz) |
||||||
|
1 |
n257, n258, n261 |
34 |
[8.2] |
[5.0] |
[20.8]-TT |
43 |
|
1 |
n260 |
31 |
[8.2] |
[5.0] |
[17.8]-TT |
43 |
|
2 |
n257, n258, n261 |
34 |
[9.3] |
[5.0] |
[19.7]-TT |
43 |
|
2 |
n260 |
31 |
[9.3] |
[5.0] |
[16.7]-TT |
43 |
|
3 |
n257, n258, n261 |
34 |
[8.0] |
[5.0] |
[21.0]-TT |
43 |
|
3 |
n260 |
31 |
[8.0] |
[5.0] |
[18.0]-TT |
43 |
|
4 |
n257, n258, n261 |
34 |
[9.2] |
[5.0] |
[19.8]-TT |
43 |
|
4 |
n260 |
31 |
[9.2] |
[5.0] |
[16.8]-TT |
43 |
|
5 |
n257, n258, n261 |
34 |
[11.2] |
[7.0] |
[15.8]-TT |
43 |
|
5 |
n260 |
31 |
[11.2] |
[7.0] |
[12.8]-TT |
43 |
|
Test requirements for a CA_nXD, CA_nXB Configuration (Cumulative aggregated BWchannel < 800MHz) |
||||||
|
1 |
n257, n258, n261 |
34 |
7.7 |
[5.0] |
[21.3]-TT |
43 |
|
1 |
n260 |
31 |
7.7 |
[5.0] |
[18.3]-TT |
43 |
|
2 |
n257, n258, n261 |
34 |
7.5 |
[5.0] |
[21.5]-TT |
43 |
|
2 |
n260 |
31 |
7.5 |
[5.0] |
[18.5]-TT |
43 |
|
3 |
n257, n258, n261 |
34 |
8.7 |
[5.0] |
[20.3]-TT |
43 |
|
3 |
n260 |
31 |
8.7 |
[5.0] |
[17.3]-TT |
43 |
|
4 |
n257, n258, n261 |
34 |
10.7 |
[7.0] |
[16.3]-TT |
43 |
|
4 |
n260 |
31 |
10.7 |
[7.0] |
[13.3]-TT |
43 |
|
Test requirements for a CA_nXG, CA_nXO, CA_nXD Configuration (Cumulative aggregated BWchannel < 400MHz) |
||||||
|
1 |
n257, n258, n261 |
34 |
5 |
[4.0] |
[25.0]-TT |
43 |
|
1 |
n260 |
31 |
5 |
[4.0] |
[22.0]-TT |
43 |
|
2 |
n257, n258, n261 |
34 |
6.5 |
[5.0] |
[22.5]-TT |
43 |
|
2 |
n260 |
31 |
6.5 |
[5.0] |
[19.5]-TT |
43 |
|
3 |
n257, n258, n261 |
34 |
9 |
[5.0] |
[20.0]-TT |
43 |
|
3 |
n260 |
31 |
9 |
[5.0] |
[17.0]-TT |
43 |
|
Test requirements for a CA_nX(D-G) )_UL_nXD, CA_nX(D-G)_UL_nXG, CA_nX(D-O)_UL_nXD, CA_nX(D-O)_UL_nXO, CA_nX(D-H)_UL_nXD, CA_nX(D-P)_UL_nXD, CA_nX(E-O)_UL_nXO, CA_nX(D-I)_UL_nXD, CA_nX(D-Q)_UL_nXD, CA_nX(G-I)_UL_nXG Configuration (Cumulative aggregated BWchannel <= 1400MHz) |
||||||
|
1 |
n257, n258, n261 |
34 |
[8.2] |
[5.0] |
[20.8]-TT |
43 |
|
1 |
n260 |
31 |
[8.2] |
[5.0] |
[17.8]-TT |
43 |
|
2 |
n257, n258, n261 |
34 |
[9.3] |
[5.0] |
[19.7]-TT |
43 |
|
2 |
n260 |
31 |
[9.3] |
[5.0] |
[16.7]-TT |
43 |
|
3 |
n257, n258, n261 |
34 |
[8.0] |
[5.0] |
[21.0]-TT |
43 |
|
3 |
n260 |
31 |
[8.0] |
[5.0] |
[18.0]-TT |
43 |
|
4 |
n257, n258, n261 |
34 |
[9.2] |
[5.0] |
[19.8]-TT |
43 |
|
4 |
n260 |
31 |
[9.2] |
[5.0] |
[16.8]-TT |
43 |
|
5 |
n257, n258, n261 |
34 |
[11.2] |
[7.0] |
[15.8]-TT |
43 |
|
5 |
n260 |
31 |
[11.2] |
[7.0] |
[12.8]-TT |
43 |
|
Test requirements for a CA_nX(D-G)_UL_nXD, CA_nX(D-O)_UL_nXD, CA_nX(D-G)_UL_nXG, CA_nX(D-O)_UL_nXO, CA_nX(D-H)_UL_nXD, CA_nX(D-P)_UL_nXD, CA_nX(O-E)_UL_nXO, CA_nX(D-I)_UL_nXD, CA_nX(D-Q)_UL_nXD, CA_nX(G-I)_UL_nXG Configuration (Cumulative aggregated BWchannel < 800MHz) |
||||||
|
1 |
n257, n258, n261 |
34 |
7.7 |
[5.0] |
[21.3]-TT |
43 |
|
1 |
n260 |
31 |
7.7 |
[5.0] |
[18.3]-TT |
43 |
|
2 |
n257, n258, n261 |
34 |
7.5 |
[5.0] |
[21.5]-TT |
43 |
|
2 |
n260 |
31 |
7.5 |
[5.0] |
[18.5]-TT |
43 |
|
3 |
n257, n258, n261 |
34 |
8.7 |
[5.0] |
[20.3]-TT |
43 |
|
3 |
n260 |
31 |
8.7 |
[5.0] |
[17.3]-TT |
43 |
|
4 |
n257, n258, n261 |
34 |
10.7 |
[7.0] |
[16.3]-TT |
43 |
|
4 |
n260 |
31 |
10.7 |
[7.0] |
[13.3]-TT |
43 |
|
Test requirements for a CA_nX(D-O)_UL_nXD, CA_nX(D-O)_UL_nXO Configuration (Cumulative aggregated BWchannel < 400MHz) |
||||||
|
1 |
n257, n258, n261 |
34 |
5 |
[4.0] |
[25.0]-TT |
43 |
|
1 |
n260 |
31 |
5 |
[4.0] |
[22.0]-TT |
43 |
|
2 |
n257, n258, n261 |
34 |
6.5 |
[5.0] |
[22.5]-TT |
43 |
|
2 |
n260 |
31 |
6.5 |
[5.0] |
[19.5]-TT |
43 |
|
3 |
n257, n258, n261 |
34 |
9 |
[5.0] |
[20.0]-TT |
43 |
|
3 |
n260 |
31 |
9 |
[5.0] |
[17.0]-TT |
43 |
|
NOTE 1: TT for each band and accumulative aggregated bandwidth is specified in Table 6.2A.2.1.5-17. |
||||||
Table 6.2A.2.1.5-16: MPR requirements for Intra-band Contiguous UL CA (Power Class 4, Non-contiguous allocation)
|
Test ID |
Band |
Min peak EIRP (dBm) |
MPR (dB) |
T(MPR) (dB) |
Lower limit (dBm) |
Upper limit (dBm) |
|
Test requirements for a CA_nXB, CA_nXD, CA_XG, CA_nXO Configuration |
||||||
|
1 |
n257, n258, n261 |
34 |
7 |
[5.0] |
[22.0]-TT |
43 |
|
1 |
n260 |
31 |
7 |
[5.0] |
[19.0]-TT |
43 |
|
2 |
n257, n258, n261 |
FFS |
FFS |
FFS |
FFS |
FFS |
|
2 |
n260 |
FFS |
FFS |
FFS |
FFS |
FFS |
|
3 |
n257, n258, n261 |
FFS |
FFS |
FFS |
FFS |
FFS |
|
3 |
n260 |
FFS |
FFS |
FFS |
FFS |
FFS |
|
NOTE 1: TT for each band and accumulative aggregated bandwidth is specified in Table 6.2A.2.1.5-17. |
||||||
Table 6.2A.2.1.5-17: Test Tolerance (MPR for CA for Power class 4)
FFS
6.2A.2.2 UE maximum output power reduction for CA (3UL CA)
FFS
6.2A.2.3 UE maximum output power reduction for CA (4UL CA)
FFS
6.2A.2.4 UE maximum output power reduction for CA (5UL CA)
FFS
6.2A.2.5 UE maximum output power reduction for CA (6UL CA)
FFS
6.2A.2.6 UE maximum output power reduction for CA (7UL CA)
FFS
6.2A.2.7 UE maximum output power reduction for CA (8UL CA)
FFS