B.6 Interworking between normal and fast power control for ECSD

05.083GPPRadio subsystem link controlTS

Interworking between normal and fast power control in the ECSD mode is done so that the normal power control may be running even if fast power control is activated. This means that both the BSS and the MS shall, at all times when in dedicated ECSD mode, estimate the radio link quality plus send power level commands and link quality reports respectively based on the cycle of the reporting period of length 104 TDMA frames (as specified in subclause 8.4). When FPC is activated though, the power level commands sent via SACCH are ignored by the MS.

Through this, a switch back to normal power control can be done very easily since the MS always knows what power level to use immediately after a switch. Switching between normal and fast power control always takes place at the beginning of a reporting period.

The figure below illustrates the simultaneous operation of the two power control mechanisms and their respective functional blocks.

The BSC has the control over which power control loop is in use. This is signalled with one control bit on the Abis interface to the BTS, which in turn informs the MS, when the fast power control loop shall be used. When FPC is not activated, there is no requirement for either the BTS nor the MS to perform quality estimations or sending commands/reports via E-IACCH.

The specific power control algorithm to be used for fast power control is, as is the case for normal power control, implementation dependent and is thus not standardised.

Annex C (informative):
Example Interference Measurement Algorithm

The following is an example algorithm for interference estimation at the MS during the Training Sequence of a normal burst (GMSK or 8PSK). The same technique may also be employed by the BTS.

The symbol spaced sampled complex envelope of the received signal r(t), {rn}, can be expressed as follows:

Where {ci} represents the tap weights of the equivalent channel, {ui} represents the complex symbols of the Training Sequence, zn represents the interference and noise contribution, and L1 and L2 are channel dispersion parameters.

STEP 1:

The channel is estimated using the first N symbols of the Training Sequence (where N < 26) as follows:

where represents the estimated equivalent channel response.

is the K x K correlation matrix of the complex symbols of Training Sequence .

denotes the K x 1 cross-correlation vector between the complex symbols of Training Sequence and the received signal sample .

and .

K will be decided based on the expected maximum equivalent channel dispersion. Note that the equivalent channel corresponds to the combined channel response of the physical channel and transmit and receive filter responses. K represents the number of symbols over which the equivalent channel dispersion is spanning. K = L1+L2+1.

STEP 2:

The interference and noise contribution (IN) is calculated for the last M = 26-N symbols of the Training Sequence as follows:

Note that the accuracy of the interference estimate will improve as M increases, on other hand the channel estimate may suffer because of a reduced N. Optionally, the symbols in the immediate vicinity on either side of the Training Sequence may also be used in estimating interference.

STEP 3:

The above procedure may be performed in both the directions scanning Training Sequence from left to right and right to left. By scanning in both the directions, IN can be obtained for the first M symbols, IN1, and for last M symbols, IN2. The interference measurement sample SSCH,n is calculated as follows.

SSCH,n = (IN1+IN2)/2

Annex D (informative):
Example Selection of Modulation and Coding Schemes based on Link Quality Reports

The table below gives examples of Modulation and Coding Scheme (MCS) selection based on the reported link quality estimates 8PSK_MEAN_BEP and 8PSK_CV_BEP. The selection is designed to maximise the link throughput. Further optimization e.g. for the IR mode is possible. In the same manner the MCS-1 to MCS-4 can be chosen based on GMSK_MEAN_BEP and GMSK_CV_BEP.

Table 3: 8PSK MCS selection based on BEP reports

8PSK_CV_BEP

1

2

3

4

5

6

7

8

8

P

S

K

M

E
A
N

B
E
P

1

MCS-5

MCS-5

MCS-5

MCS-5

MCS-5

MCS-5

MCS-5

MCS-5

2

MCS-5

MCS-5

MCS-5

MCS-5

MCS-5

MCS-5

MCS-5

MCS-5

3

MCS-5

MCS-5

MCS-5

MCS-5

MCS-5

MCS-5

MCS-5

MCS-5

4

MCS-5

MCS-5

MCS-5

MCS-5

MCS-5

MCS-5

MCS-5

MCS-5

5

MCS-5

MCS-5

MCS-5

MCS-5

MCS-5

MCS-5

MCS-5

MCS-5

6

MCS-5

MCS-5

MCS-5

MCS-5

MCS-5

MCS-5

MCS-5

MCS-6

7

MCS-5

MCS-5

MCS-5

MCS-5

MCS-5

MCS-5

MCS-6

MCS-6

8

MCS-5

MCS-5

MCS-5

MCS-5

MCS-5

MCS-6

MCS-6

MCS-6

9

MCS-5

MCS-5

MCS-5

MCS-5

MCS-6

MCS-6

MCS-6

MCS-6

10

MCS-5

MCS-5

MCS-5

MCS-6

MCS-6

MCS-6

MCS-6

MCS-6

11

MCS-5

MCS-5

MCS-6

MCS-6

MCS-6

MCS-6

MCS-6

MCS-7

12

MCS-6

MCS-6

MCS-6

MCS-6

MCS-6

MCS-6

MCS-7

MCS-7

13

MCS-6

MCS-6

MCS-6

MCS-6

MCS-6

MCS-7

MCS-7

MCS-7

14

MCS-6

MCS-6

MCS-6

MCS-6

MCS-7

MCS-7

MCS-7

MCS-7

15

MCS-6

MCS-6

MCS-7

MCS-7

MCS-7

MCS-7

MCS-7

MCS-7

16

MCS-7

MCS-7

MCS-7

MCS-7

MCS-7

MCS-7

MCS-7

MCS-7

17

MCS-7

MCS-7

MCS-7

MCS-7

MCS-7

MCS-7

MCS-7

MCS-7

18

MCS-7

MCS-7

MCS-7

MCS-7

MCS-7

MCS-7

MCS-7

MCS-7

19

MCS-7

MCS-7

MCS-7

MCS-7

MCS-7

MCS-7

MCS-7

MCS-7

20

MCS-7

MCS-7

MCS-7

MCS-7

MCS-7

MCS-7

MCS-7

MCS-7

21

MCS-7

MCS-7

MCS-7

MCS-7

MCS-7

MCS-7

MCS-7

MCS-7

22

MCS-7

MCS-7

MCS-8

MCS-8

MCS-8

MCS-8

MCS-8

MCS-8

23

MCS-8

MCS-8

MCS-8

MCS-8

MCS-8

MCS-8

MCS-8

MCS-8

24

MCS-8

MCS-8

MCS-8

MCS-8

MCS-8

MCS-8

MCS-8

MCS-8

25

MCS-8

MCS-8

MCS-8

MCS-8

MCS-8

MCS-8

MCS-8

MCS-8

26

MCS-8

MCS-8

MCS-8

MCS-8

MCS-8

MCS-8

MCS-8

MCS-8

27

MCS-8

MCS-8

MCS-8

MCS-8

MCS-8

MCS-8

MCS-8

MCS-8

28

MCS-8

MCS-8

MCS-8

MCS-8

MCS-8

MCS-8

MCS-8

MCS-8

29

MCS-9

MCS-9

MCS-9

MCS-9

MCS-9

MCS-9

MCS-9

MCS-9

30

MCS-9

MCS-9

MCS-9

MCS-9

MCS-9

MCS-9

MCS-9

MCS-9

31

MCS-9

MCS-9

MCS-9

MCS-9

MCS-9

MCS-9

MCS-9

MCS-9

32

MCS-9

MCS-9

MCS-9

MCS-9

MCS-9

MCS-9

MCS-9

MCS-9

Annex E (informative):
Change history

SPEC

SMG#

CR

Rev

PHS

VERS

NEW_V

SUBJECT

05.08

s24

A043

R97

5.5.0

6.0.0

Channel Quality Report in GPRS

05.08

s25

A046

R97

6.0.0

6.1.0

Improvements to GPRS power control

05.08

s25

A047

R97

6.0.0

6.1.0

Cell re-selection in GPRS

05.08

s25

A050

R97

6.0.0

6.1.0

Cell re-selection in GPRS

05.08

s25

A051

R97

6.0.0

6.1.0

GPRS Cell Re-selection

05.08

s25

A053

R97

6.0.0

6.1.0

Interference measurements for GPRS

05.08

s25

A054

R97

6.0.0

6.1.0

Renaming of GPRS RR states

05.08

s25

A055

R97

6.0.0

6.1.0

Transmission on downlink PDCH

05.08

s25

A056

R97

6.0.0

6.1.0

RF power level control during configuration change procedure

05.08

6.1.0

6.1.1

Correction of version number

05.08

s26

A057

R97

6.1.0

6.2.0

Corrections and clarifications to GPRS

05.08

s26

A058

R97

6.1.0

6.2.0

Cell re-selection in GPRS

05.08

s26

A059

R97

6.1.0

6.2.0

Mapping of PACCH

05.08

s26

A060

R97

6.1.0

6.2.0

Coding of parameter GCH

05.08

s26

A061

R97

6.1.0

6.2.0

RXQUAL measurement

05.08

s26

A063

R97

6.1.0

6.2.0

Clarification of non-DRX mode

05.08

s26

A064

R97

6.1.0

6.2.0

Release of dedicated channels

05.08

s26

A065

R97

6.1.0

6.2.0

Renaming of broadcast parameters

05.08

s26

A066

R97

6.1.0

6.2.0

Measurement reporting and network controlled cell selection

05.08

s27

A044

R97

6.2.0

6.3.0

MS delay time in reporting a new strongest neighbouring cell

05.08

s27

A068

R97

6.2.0

6.3.0

Clarification of Power Control

05.08

s27

A069

R97

6.2.0

6.3.0

Measurement reporting

05.08

s27

A072

R97

6.2.0

6.3.0

GPRS idle mode measurements

05.08

s27

A074

R97

6.2.0

6.3.0

Clarification of Complete BA (SACCH)

05.08

s27

A075

R97

6.2.0

6.3.0

Tolerances for power control

05.08

s27

A076

R97

6.2.0

6.3.0

GPRS downlink power control

05.08

s28

A080

R97

6.3.0

6.4.0

MS delay time in reporting a new strongest neighbouring cell in GPRS

05.08

s28

A081

R97

6.3.0

6.4.0

Cell re-selection

05.08

s28

A082

R97

6.3.0

6.4.0

Interference measurements on Network command

05.08

s28

A086

R97

6.3.0

6.4.0

Clarification of received signal level

05.08

s28

A087

R97

6.3.0

6.4.0

Interference measurements with frequency hopping

05.08

s28

A088

R97

6.3.0

6.4.0

Clarification of interference measurements

05.08

s28

A089

R97

6.3.0

6.4.0

Call reestablishment procedure for abnormal release

with cell reselection in ready state

05.08

s28

A093

R97

6.3.0

6.4.0

Application time of Gamma and Alpha parameters for the computation on MS output power

05.08

s28

A094

R97

6.3.0

6.4.0

Clarification on MAFA measurement requirements

05.08

s28

A096

R97

6.3.0

6.4.0

Cell reselection delay time in packet transfer mode

05.08

s28

A097

R97

6.3.0

6.4.0

Clarification to a requirement to perform the interference measurements

05.08

s28

A098

R97

6.3.0

6.4.0

Neighbour measurements

05.08

s28

A099

R97

6.3.0

6.4.0

End of measurement period for the quality measurements

05.08

s28

A102

R97

6.3.0

6.4.0

Correction to I_LEVEL reporting

05.08

s28

A079

R98

6.4.0

7.0.0

Harmonization between GSM and PCS 1 900 standard

05.08

s28

A084

R98

6.4.0

7.0.0

Introduction of CTS in 05.08

05.08

s28

A100

R98

6.4.0

7.0.0

AMR DTX aspects in signal quality measurements

05.08

s29

A070

R98

7.0.0

7.1.0

Addition of SoLSA functionality

05.08

s29

A104

R98

7.0.0

7.1.0

Clarification of CTS-MS initial synchronization

05.08

s29

A105

R98

7.0.0

7.1.0

Performance of CTS power control algorithm

05.08

s29

A106

R98

7.0.0

7.1.0

Introduction of quality criteria in CTS idle mode

05.08

s29

A107

R98

7.0.0

7.1.0

Clarification of C2_CTS computation

05.08

s29

A108

R98

7.0.0

7.1.0

Clarification of range delay measurements

05.08

s29

A116

R98

7.0.0

7.1.0

Time to be ready to access a new cell

05.08

s29

A123

R98

7.0.0

7.1.0

Clarification of time of application of new alpha and

gamma value in case of time slot reconfiguration

05.08

s29

A127

R98

7.0.0

7.1.0

Relation between NC_REPORTING_PERIOD and DRX

period

05.08

s29

A131

R98

7.0.0

7.1.0

Interference measurement on packet idle mode

05.08

s29

A132

R98

7.0.0

7.1.0

Clarification to the interference measurements requirements in packet idle mode

05.08

s29

A133

R98

7.0.0

7.1.0

Cell selection parameters in Packet Measurement Order

05.08

s29

A134

R98

7.0.0

7.1.0

Calculation of SIGN_VAR

05.08

s29

A135

R98

7.0.0

7.1.0

Updating of PBCCH information

05.08

s29

A137

R98

7.0.0

7.1.0

Downlink Power Control for GPRS

05.08

s29

A141

R98

7.0.0

7.1.0

Periodic search for SoLSA cell in idle mode

05.08

s29

A145

R98

7.0.0

7.1.0

PC_MEAS_CHAN in case of downlink power control

05.08

s29

A146

R98

7.0.0

7.1.0

RXQUAL in CS4

05.08

s29

A150

R98

7.0.0

7.1.0

Corrections to cell selection for GPRS

05.08

s29

A151

R98

7.0.0

7.1.0

Clarifications to network controlled cell re-selection

05.08

s29

A153

R98

7.0.0

7.1.0

Clarification to network controlled cell re-selection

05.08

s29

A085

R99

7.1.0

8.0.0

EDGE on the BCCH carrier

05.08

s29

A144

R99

7.1.0

8.0.0

GSM 400 bands introduced in 05.08

05.08

s30

A158

R99

8.0.0

8.1.0

Clarification of idle mode support for SoLSA

05.08

s30

A162

R99

8.0.0

8.1.0

Cell re-selection when PBCCH does not exist

05.08

s30

A165

R99

8.0.0

8.1.0

Correction of C filtering

05.08

s30

A168

R99

8.0.0

8.1.0

Clarification of extended measurements

05.08

s30

A170

R99

8.0.0

8.1.0

Multiband cell selection and reporting

05.08

s30

A173

R99

8.0.0

8.1.0

Cell selection parameters in NC_FREQUENCY_LIST

05.08

s30

A176

R99

8.0.0

8.1.0

Power control measurements

05.08

s30

A179

R99

8.0.0

8.1.0

Clarification of RXQUAL for CS4

05.08

s30

A185

R99

8.0.0

8.1.0

Clarification to interference measurements in packet mode changes

05.08

s30

A188

R99

8.0.0

8.1.0

Correction of fixed allocation mode reference that should be "half duplex mode"

05.08

s30

A193

R99

8.0.0

8.1.0

Downlink Power Control for GPRS

05.08

s30b

A147

R99

8.1.0

8.2.0

Fast Power Control for ECSD

05.08

s30b

A180

R99

8.1.0

8.2.0

COMPACT Cell Selection and Reselection

05.08

s30b

A181

R99

8.1.0

8.2.0

Link Quality Control measurements for EGPRS

05.08

s30b

A199

R99

8.1.0

8.2.0

Interference measurements – Alignment 05.08 to 04.60

05.08

s30b

A202

R99

8.1.0

8.2.0

Clarification of channel quality reporting period

05.08

s30b

A206

R99

8.1.0

8.2.0

Downlink Power Control

05.08

s30b

A222

R99

8.1.0

8.2.0

Clarification of timeslots on which to make inerference measurements

05.08

s30b

A228

R99

8.1.0

8.2.0

Interference measurements in packet idle mode

05.08

MCC

R99

8.2.0

8.2.1

Figures B1 and also B2 have been updated according to the agreed CR A057. The changes have been missed due to the lack of revision marks.

05.08

s31

A203

R99

8.2.1

8.3.0

COMPACT interference measurements

05.08

s31

A207

R99

8.2.1

8.3.0

Enhanced Measurement Reporting

05.08

s31

A231

R99

8.2.1

8.3.0

Clarification of Extended Measurement requirements

05.08

s31

A232

R99

8.2.1

8.3.0

Correction of measurement filtering for power control

05.08

s31

A233

R99

8.2.1

8.3.0

Enhanced Measurement Reporting for (E)GPRS

05.08

s31

A234

R99

8.2.1

8.3.0

COMPACT RF power control

05.08

s31

A240

R99

8.2.1

8.3.0

EGPRS Link Quality Control measurements

05.08

s31

A243

R99

8.2.1

8.3.0

Missing GSM 850 requirements for Classic BCCH

05.08

s31

A244

R99

8.2.1

8.3.0

Introduction of Example of EGPRS Link Adaptation Algorithm

05.08

s31b

A242

R99

8.3.1

8.4.0

Inter System Handover and Cell re-selection

05.08

s31b

A248

R99

8.3.1

8.4.0

Removal of parameter CELL_RESELECT_PARAM_IND

05.08

s31b

A270

R99

8.3.1

8.4.0

Procedures for inter-system handover (cdma2000)

05.08

s31b

A252

R99

8.3.1

8.4.0

Correction to mapping of interference levels

05.08

s31b

A253

R99

8.3.1

8.4.0

Clarification on Abnormal Cell Reselection

05.08

s31b

A269

R99

8.3.1

8.4.0

System Information refreshing in idle mode

05.08

s31b

A271

R99

8.3.1

8.4.0

MS behaviour under network controlled cell reselection

05.08

s31b

A272

R99

8.3.1

8.4.0

Cell selection parameter acquisition in Packet Transfer mode

05.08

s31b

A273

R99

8.3.1

8.4.0

BTS Output Power

05.08

s31b

A274

R99

8.3.1

8.4.0

Default value for GPRS_MS_TXPWR_MAX_CCH at cell re-selection

05.08

s31b

A249

R99

8.3.1

8.4.0

Clarification of Cell Bar Qualify 2 parameter

05.08

s31b

A266

R99

8.3.1

8.4.0

Fast inband signalling: E-IACCH

05.08

s31b

A268

R99

8.3.1

8.4.0

EGPRS Link Quality measurements

05.08

s32

A275

R99

8.4.0

8.5.0

COMPACT interference measurements

05.08

s32

A276

R99

8.4.0

8.5.0

Class A Dual Transfer Mode (DTM)

05.08

s32

A278

R99

8.4.0

8.5.0

Corrections to Inter system Handover and Cell re-selection

05.08

s32

A279

R99

8.4.0

8.5.0

Definition of the SCALE parameter for RXLEV reporting

05.08

s32

A280

R99

8.4.0

8.5.0

Clarification GPRS downlink transmission requirements

05.08

s32

A281

R99

8.4.0

8.5.0

Correction of inconsistency in the handling of BEP_PERIOD2

05.08

s32

A282

R99

8.4.0

8.5.0

Cell_Bar_Access_2 missing in 05.08

05.08

s32

A283

R99

8.4.0

8.5.0

Clarifications on EGPRS measurements

Change history

Date

TSG 

GERAN#

TSG Doc.

CR

Rev

Subject/Comment

Old

New

2000-09

01

GP-000335

A287

1

Extended measurement report (MAFA)

8.5.0

8.6.0

2000-09

01

GP-000361

A288

1

Clarifications on EGPRS Quality parameters

8.5.0

8.6.0

2000-09

01

GP-000336

A289

1

Editorial corrections

8.5.0

8.6.0

2000-09

01

GP-000362

A290

1

Clarifications of interference measurements for COMPACT

8.5.0

8.6.0

2000-09

01

GP-000330

A291

1

Corrections to Inter System Handover and Cell re-selection

8.5.0

8.6.0

2000-09

01

GP-000325

A296

1

BTS RF power control

8.5.0

8.6.0

2000-09

01

GP-000328

A297

Correction to measurement reporting for DTM

8.5.0

8.6.0

2000-09

01

GP-000364

A298

1

Corrections to BSIC decoding

8.5.0

8.6.0

2000-11

02

GP-000843

A299

1

EGPRS Channel Quality Report reporting period

8.6.0

8.7.0

2000-11

02

GP-000577

A300

GPRS neighbour cell measurement exceptions

8.6.0

8.7.0

2000-11

02

GP-000904

A301

2

Corrections to Handover and Cell re-selection

8.6.0

8.7.0

2000-11

02

GP-000871

A302

1

Corrections to Enhanced Measurement Reporting

8.6.0

8.7.0

2000-11

02

GP-000873

A303

1

Maximum number of neighbour cell carriers to be monitored by the MS

8.6.0

8.7.0

2000-11

02

GP-000877

A305

1

Discontinuous transmission

8.6.0

8.7.0

2000-11

02

GP-000851

A306

Measurement requirements for COMPACT MS in the case of multislot allocations

8.6.0

8.7.0

2000-11

02

GP-000882

A307

1

GPRS cell reselection with Packet Measurement Order

8.6.0

8.7.0

2000-11

02

Front page layout correction

8.7.0

8.7.1

2001-01

03

GP-010057

A308

Handling of missing gamma values

8.7.1

8.8.0

2001-01

03

GP-010097

A309

Removal of Anonymous Access

8.7.1

8.8.0

2001-01

03

GP-010105

A310

Measurements during polling response transmission

8.7.1

8.8.0

2001-01

03

GP-010126

A311

Fine tuning of GPRS cell reselection

8.7.1

8.8.0

2001-01

03

GP-010203

A312

Multi-RAT measurements

8.7.1

8.8.0

2001-01

03

GP-010376

A313

1

3G Cell re-selection with only frequency information

8.7.1

8.8.0

2001-01

03

GP-010438

A314

1

Addition of GSM Blind handover requirement

8.7.1

8.8.0

2001-04

04

GP-010797

A315

1

Blind Cell re-selection synchronisation failure

8.8.0

8.9.0

2001-04

04

GP-010577

A316

Editorial correction to measurement reporting

8.8.0

8.9.0

2001-04

04

GP-010654

A317

Clarifications on System Information Type 2 quater decoding

8.8.0

8.9.0

2001-04

04

GP-010657

A318

Correction on NBR_RCVD_BLOCKS counting

8.8.0

8.9.0

2001-04

04

GP-010914

A321

Introduction of UTRAN blind search from the PSI3 quater

8.8.0

8.9.0

2001-06

05

GP-011415

A322

2

Clarifications due to equivalent PLMN

8.9.0

8.10.0

2001-06

05

GP-011043

A323

Missing default values for measurement parameters

8.9.0

8.10.0

2001-06

05

GP-011046

A324

Invalid BSIC: Terminology alignment

8.9.0

8.10.0

2001-08

06

GP-011861

A330

1

Correction to Predefined Configurations

8.10.0

8.11.0

2001-08

06

GP-011864

A332

1

3G reselection: suitable cell and amount to monitor

8.10.0

8.11.0

2001-08

06

GP-011524

A335

RXQUAL_SUB and RXLEV_SUB with AMR-NB

8.10.0

8.11.0

2001-11

07

GP-012221

A336

Clarification on Packet Enhanced Measurement Reporting

8.11.0

8.12.0

2001-11

07

GP-012395

A338

Number of cells/frequencies to be monitored by a dual mode terminal

8.11.0

8.12.0

2001-11

07

GP-012759

A339

1

Correction of parameters related to enhanced and 3G measurements

8.11.0

8.12.0

2001-11

07

GP-012488

A340

Clarification on UTRAN FDD RSSI reporting

8.11.0

8.12.0

2001-11

07

GP-012497

A343

Alignment of predefined configuration handling according to RAN 2 views

8.11.0

8.12.0

2002-02

08

GP-020509

A348

1

3G-GSM clarification on RSSI, FDD valid cell and MULTIRAT_REPORTING

8.12.0

8.13.0

2002-04

09

GP-020649

A349

NBR_RCVD_BLOCKS for 14.4 non-transparent data

8.13.0

8.14.0

2002-04

09

GP-021004

A356

Clarification to priorities between GPRS interference measurements and InterRAT measurements

8.13.0

8.14.0

2002-06

10

GP-021416

A357

Correction on the applicability of reporting priority

8.14.0

8.15.0

2002-06

10

GP-021420

A358

EMR in case of signalling only mode

8.14.0

8.15.0

2002-06

10

GP-021423

A359

Correction to cell reselection time requirement (GSM to UTRAN FDD)

8.14.0

8.15.0

2002-06

10

GP-022065

A362

2

Removal of CBQ2

8.14.0

8.15.0

2002-06

10

GP-021926

A364

1

Correction: validity period of NC_FREQUENCY_LIST

8.14.0

8.15.0

2003-04

14

GP-030976

A366

1

Use of unbiased variance in the computation of CV_BEP

8.15.0

8.16.0

2003-06

15

GP-031719

A369

2

Missing Test Measurement Parameters for UTRAN TDD Cell Access

8.16.0

8.17.0

2003-08

16

GP-032225

A370

2

Modification of accuracy requirements for MEAN_BEP for EGPRS

8.17.0

8.18.0

2003-08

16

GP-031780

A371

1

Correction on DTM power control

8.17.0

8.18.0

2003-08

16

GP-031984

A372

Correction for identification of TDD cells

8.17.0

8.18.0

2003-08

16

GP-032181

A374

1

Clarification to Extended Dynamic Allocation for high multislot classes

8.17.0

8.18.0

2003-08

16

GP-032221

A375

1

Correction of insufficient range of the FDD_Qmin parameter

8.17.0

8.18.0

2003-11

17

GP-032763

A376

1

Correction of applicability of NC measurement reporting parameters in context with dedicated mode connections

8.18.0

8.19.0

2004-06

20

GP-041261

A377

Applicability of individual NC parameters

8.19.0

8.20.0

2004-06

20

GP-041692

A378

Correction of DTM Output Power Control

8.19.0

8.20.0

2004-08

21

GP-041918

A379

CPICH RSCP based criterion for GERAN to UTRAN FDD cell reselection

8.20.0

8.21.0

2004-11

22

GP-042451

A380

2

Downlink power control for DTM

8.21.0

8.22.0

2005-11

27

GP-052746

A382

1

Accuracy requirements of MS MEAN_BEP estimation

8.22.0

8.23.0